Driver Side Door Entry Lock Function does not Operate
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
If the driver door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. As a faulty part, the entry lock switch circuit (certification ECU (smart key ECU assembly) → driver side door outside handle (entry lock switch) → driver side door electrical key oscillator) can be considered.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".
| 1. CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).
- OK:
- Locked doors unlock.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body (Main Body ECU (Instrument Panel Junction Block)) Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Lock Pos SW
Driver door lock position switch signal/LOCK or UNLOCK
ON: Driver side door is unlocked
OFF: Driver side door is locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
- Result:
Result
Proceed to
OK
A
NG
B
(Proceed to "Driver Door LOCK/UNLOCK Functions do not Operate")
|
|
||||
| A | |
| 3. READ VALUE ON INTELLIGENT TESTER (DOOR OUTSIDE HANDLE) |
Select D Trigger SW in the Data List and read the tester display.
Entry & Start (Certification ECU (Smart Key ECU Assembly)): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Trigger SW
Driver side door lock switch / ON or OFF
ON: Entry lock switch is pressed
OFF: Entry lock switch is not pressed
-
- OK:
- On the tester screen, the item changes between ON and OFF according to the chart above.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) |
Remove the front door outside handle (Click here).

Disconnect the door electrical key oscillator connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
z13-1 (TRG-) - z14-9 (TRG-)
Always
Below 1 Ω
z13-1 (TRG-) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
z15-1 (TRG-) - z16-9 (TRG-)
Always
Below 1 Ω
z15-1 (TRG-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the certification ECU (smart key ECU assembly) connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
D36-3 (TSW1) - z13-3 (TRG+)
Always
Below 1 Ω
D36-3 (TSW1) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
D36-3 (TSW1) - z15-3 (TRG+)
Always
Below 1 Ω
D36-3 (TSW1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT FRONT DOOR OUTSIDE HANDLE (DRIVER SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
z13-1 (TRG-) - z13-3 (TRG+)
Lock switch not pushed
10 kΩ or higher
z13-1 (TRG-) - z13-3 (TRG+)
Lock switch pushed
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
z15-1 (TRG-) - z15-3 (TRG+)
Lock switch not pushed
10 kΩ or higher
z15-1 (TRG-) - z15-3 (TRG+)
Lock switch pushed
Below 1 Ω
|
|
||||
| OK | |
| 7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry functions operate normally.
- OK:
- Entry functions operate normally.
|
|
||||
| OK | ||
| ||
