2007-2013 Highlander Kluger · Service Manual ENGINE

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The fuel injector assemblies are located on the intake manifold. They inject fuel into the cylinders based on signals from the ECM.

WIRING DIAGRAM

A172778E08
A172779E12

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

  1. A194105E55
    Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B13-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B14-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B15-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B16-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B17-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B18-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Reconnect the fuel injector assembly connector.



NG
Go to step 4
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B13-1 - B47-6 (#10)
    Always
    Below 1 Ω
    B14-1 - B47-1 (#20)
    Always
    Below 1 Ω
    B15-1 - B47-7 (#30)
    Always
    Below 1 Ω
    B16-1 - B47-2 (#40)
    Always
    Below 1 Ω
    B17-1 - B47-8 (#50)
    Always
    Below 1 Ω
    B18-1 - B47-3 (#60)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B13-1 or B47-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B14-1 or B47-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B15-1 or B47-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B16-1 or B47-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B17-1 or B47-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-1 or B47-3 (#60) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the fuel injector assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connector.

  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B13-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω
    B14-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω
    B15-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω
    B16-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω
    B17-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω
    B18-2 - 3 (IG2 relay terminal)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B13-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    B14-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    B15-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    B16-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    B17-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    B18-2 or 3 (IG2 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the fuel injector assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← Fuel Injector Circuit (Aug 2008 – Jun 2010)Starter Signal Circuit (May 2007 – Jul 2008) →