2007-2013 Highlander Kluger · Service Manual BODY

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

If the passenger side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window switch, power window master switch or wire harness.

WIRING DIAGRAM

B175981E01

INSPECTION PROCEDURE


1. CHECK POWER WINDOW SWITCH (FRONT PASSENGER SIDE) (POWER SOURCE)

  1. B175982E01
    Disconnect the G7 connector (LHD).

  1. Disconnect the H10 connector (RHD).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    G7-3 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    H10-3 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT POWER WINDOW SWITCH (FRONT PASSENGER SIDE)

  1. B164433E08
    Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    3 (B) - 4 (U)
    Below 1 Ω
    1 (D) - 2 (SD)
    OFF
    Below 1 Ω
    4 (U) - 5 (SU)
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    Below 1 Ω



NG
REPLACE POWER WINDOW SWITCH (FRONT PASSENGER SIDE) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SWITCH (FRONT PASSENGER SIDE) - MOTOR (FRONT PASSENGER SIDE))

  1. B175983E01
    Disconnect the G7 and G1 connectors (LHD).

  1. Disconnect the H10 and H8 connectors (RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    G7-4 (U) - G1-2 (U)
    Always
    Below 1 Ω
    G7-1 (D) - G1-1 (D)
    Always
    Below 1 Ω
    G7-4 (U) - Body ground
    Always
    10 kΩ or higher
    G7-1 (D) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    H10-4 (U) - H8-2 (U)
    Always
    Below 1 Ω
    H10-1 (D) - H8-1 (D)
    Always
    Below 1 Ω
    H10-4 (U) - Body ground
    Always
    10 kΩ or higher
    H10-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE)

  1. Check power window regulator motor operation.

    1. Remove the power window regulator motor (Click here).B164425E02

    2. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

      OK:
      Measurement Condition
      Specified Condition
      Battery negative (-) → Terminal 2
      Battery positive (+) → Terminal 1
      Motor gear rotates clockwise
      Battery negative (-) → Terminal 1
      Battery positive (+) → Terminal 2
      Motor gear rotates counterclockwise

  1. Check PTC operation:

    NOTICE:
    The work must be performed with the power window regulator and door glass installed on the vehicle.

    1. Install the power window regulator motor (Click here).

    2. B164428E17
      Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.

      NOTICE:
      Match the arrow mark of the probe with the direction of the current flow.

    3. Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.

    4. Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

      Standard:
      4 to 90 seconds

    5. 60 seconds after the previous step, press the power window DOWN switch (passenger side).

      OK:
      The passenger side window goes down.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (FRONT PASSENGER SIDE))

  1. B175975E07
    for LHD:
    1. Front passenger side:Disconnect the M1 and G7 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-16 (U) - G7-5 (SU)
      Always
      Below 1 Ω
      M1-15 (D) - G7-2 (SD)
      Always
      Below 1 Ω
      M1-16 (U) - Body ground
      Always
      10 kΩ or higher
      M1-15 (D) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. B175975E08
      Front passenger side:Disconnect the L1 and H10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-12 (U) - H10-5 (SU)
      Always
      Below 1 Ω
      L1-13 (D) - H10-2 (SD)
      Always
      Below 1 Ω
      L1-12 (U) - Body ground
      Always
      10 kΩ or higher
      L1-13 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)


← Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (May 2007 – Jul 2008)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Jul 2010) →