Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
This circuit sends an operation signal from the steering pad switch to the navigation receiver assembly.If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as to if the switch were continuously pressed. Therefore, the navigation receiver assembly cannot be operated using the steering pad switch, and the navigation receiver assembly itself cannot function.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
| 1. INSPECT NAVIGATION RECEIVER ASSEMBLY |
Disconnect navigation receiver assembly connector E2.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
E2-7 (SW1) - E2-6 (SWG)
No switch is pushed
Approx. 100 kΩ
E2-7 (SW1) - E2-6 (SWG)
SEEK+ switch: pushed
0 to 2.5 Ω
E2-7 (SW1) - E2-6 (SWG)
SEEK- switch: pushed
Approx. 0.3 kΩ
E2-7 (SW1) - E2-6 (SWG)
VOL+ switch: pushed
Approx. 1 kΩ
E2-7 (SW1) - E2-6 (SWG)
VOL- switch: pushed
Approx. 3.1 kΩ
E2-8 (SW2) - E2-6 (SWG)
No switch is pushed
Approx. 100 kΩ
E2-8 (SW2) - E2-6 (SWG)
MODE switch: pushed
0 to 2.5 Ω
E2-8 (SW2) - E2-6 (SWG)
VOICE switch: pushed
Approx. 3.1 kΩ
E2-8 (SW2) - E2-6 (SWG)
ON HOOK switch: pushed
Approx. 0.3 kΩ
E2-8 (SW2) - E2-6 (SWG)
OFF HOOK switch: pushed
Approx. 1 kΩ
|
|
||||
| OK | ||
| ||
| 2. INSPECT SPIRAL CABLE |
Disconnect the steering pad switch and spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
z2-8 (EAU) - D53-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-10 (AU1) - D53-6 (AU1)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-9 (AU2) - D53-5 (AU2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.
- HINT:
- REMOVAL (Click here)
- INSTALLATION (Click here)
- REMOVAL (Click here)
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect steering pad switch assembly connector z2.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
z2-10 (AU1) - z2-8 (EAU)
No switch is pushed
Approx. 100 kΩ
z2-10 (AU1) - z2-8 (EAU)
SEEK+ switch: pushed
0 to 2.5 Ω
z2-10 (AU1) - z2-8 (EAU)
SEEK- switch: pushed
Approx. 0.3 kΩ
z2-10 (AU1) - z2-8 (EAU)
VOL+ switch: pushed
Approx. 1 kΩ
z2-10 (AU1) - z2-8 (EAU)
VOL- switch: pushed
Approx. 3.1 kΩ
z2-9 (AU2) - z2-8 (EAU)
No switch is pushed
Approx. 100 kΩ
z2-9 (AU2) - z2-8 (EAU)
MODE switch: pushed
0 to 2.5 Ω
z2-9 (AU2) - z2-8 (EAU)
VOICE switch: push
Approx. 3.1 kΩ
z2-9 (AU2) - z2-8 (EAU)
ON HOOK switch: pushed
Approx. 0.3 kΩ
z2-9 (AU2) - z2-8 (EAU)
OFF HOOK switch: pushed
Approx. 1 kΩ
|
|
||||
| OK | ||
| ||
