2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Engine Coolant Temperature Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

In this circuit, the meter CPU receives engine coolant temperature signals from the ECM using the CAN communication lines (CAN No. 1 Bus). The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E143767E07

INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Perform troubleshooting with the "SFI System" (Click here for 2GR-FE).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    Low, Normal, Hi
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/Min.: 0°C (32°F), Max.: 127.5°C (261.5°F)
    After warming up: 80 to 95°C (176 to 203°F)
    1. If -40°C (-40°F): Sensor circuit open
    2. If 140°C (284°F) or more: Sensor circuit shorted

    OK:
    Engine coolant temperature value displayed on the tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    Engine and ECT: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature/Min.: -40°C (-40°F), Max.: 140°C (284°F)
    After warming up: 80 to 100°C (176 to 212°F)
    -

    OK:
    Engine coolant temperature value displayed on the tester is almost the same as the actual engine coolant temperature.



NG
REPLACE ECM (Click here)
OK


5. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or a normal one (Click here).

    OK:
    The operation of the combination meter assembly returns to normal.



NG
REPLACE ECM (Click here)
OK

END


← Fuel Receiver Gauge Malfunction (from Jul 2012)Engine Coolant Temperature Receiver Gauge Malfunction (Aug 2008 – Jun 2010) →