2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

01-D6 No Master

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
01-D6
*1
When either of the following conditions is met:
  1. The component which has stored the code has (had) been disconnected while the ignition switch is (was) on (IG or ACC).
  1. The master device has (had) been disconnected when this code is stored.
  1. Navigation receiver assembly power source circuit
  1. Power source circuit of the component which has stored this code
  1. AVC-LAN circuit between the navigation receiver assembly and the component which has stored this code
  1. Component which has stored this code
  1. Navigation receiver assembly
01-D7
*2
When either of the following conditions is met:
  1. The component which has stored the code has (had) been disconnected after the engine starts (started).
  1. The master device has (had) been disconnected when this code is (was) stored.

HINT:
  1. *1: Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.
  2. *2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch on (IG or ACC), this code is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The navigation receiver assembly is the master unit.
  3. Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read DESCRIPTION before performing the following procedures.


1. CHECK NAVIGATION RECEIVER ASSEMBLY POWER SOURCE CIRCUIT
Refer to the "Navigation Receiver Assembly Power Source Circuit" (Click here).
If the power source circuit is operating normally, proceed to the next step.

NEXT


2. IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE

  1. E136189E11
    Enter the diagnostic mode.

  1. Press the "LAN Mon" switch to change to "LAN Monitor" mode.

  1. Identify the component which has stored this code.

    Component Table: 
    Display
    Component
    CAMERA-C
    Television camera ECU

    HINT:
    "AVN" is the component which has stored this code in the example shown in the illustration.


NEXT


3. CHECK POWER SOURCE CIRCUIT OF COMPONENT WHICH HAS STORED THIS CODE
  1. Inspect the power source circuit of the component which has stored this code.If the power source circuit is operating normally, proceed to the next step.

    Component Table: 
    Component
    Proceed to
    Television camera ECU (CAMERA-C)
    Television camera ECU power source circuit (Click here)


NEXT


4. INSPECT NAVIGATION RECEIVER ASSEMBLY
E153731E01
  1. Disconnect navigation receiver assembly connector E2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-9 (TX+) - E2-10 (TX-)
    Always
    60 to 80 Ω



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR

HINT:
For details of the connectors, refer to "TERMINALS OF ECU" (Click here).

  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the navigation receiver assembly and the component which has stored this code.

    1. Disconnect all connectors between the navigation receiver assembly and the component which has stored this code.

    2. Check for an open or short in the AVC-LAN circuit between the navigation receiver assembly and the component which has stored this code.E153704E01

      OK:
      There is no open or short circuit.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE COMPONENT WHICH HAS STORED THIS CODE
  1. Replace the component which has stored this code with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END


← 01-D6 No Master (+ 01-D7) (May 2007 – Jul 2008)01-DC Transmission Error (May 2007 – Jul 2008) →