Check CAN Bus Lines for Short Circuit (RHD Models)
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
There may be a short circuit in the CAN main wire and/or CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
- Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR CTR) |
Turn the ignition switch off.
Disconnect the CAN junction connector CTR.
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D47-1 (CANH) - D47-12 (CANL)
SB - W
CAN junction connector RH
Ignition switch off
108 to 132 Ω
D47-4 (CANH) - D47-15 (CANL)
L - W
DLC3
Ignition switch off
1 MΩ or higher
D47-5 (CANH) - D47-16 (CANL)
R - W
ECM
Ignition switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (DLC3 branch wire)
B
NG (ECM main wire)
C
NG (CAN junction connector RH main wire)
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR CTR) |
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D47-2 (CANH) - D47-13 (CANL)
V - W
Yaw rate sensor
Ignition switch off
1 MΩ or higher
D47-3 (CANH) - D47-14 (CANL)
Y - W
Center airbag sensor assembly
Ignition switch off
1 MΩ or higher
D47-6 (CANH) - D47-17 (CANL)
P - W
Air conditioning amplifier
Ignition switch off
1 MΩ or higher
D47-8 (CANH) - D47-19 (CANL)
GR - W
Main body ECU
Ignition switch off
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (Yaw rate sensor branch wire)
B
NG (Center airbag sensor assembly branch wire)
C
NG (Air conditioning amplifier branch wire)
D
NG (Main body ECU branch wire)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE) |
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-5 (CANH) - D47-16 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 4. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR RH) |
Disconnect the CAN junction connector RH.
Measure the resistance according to the value(s) in the table below.


- HINT:
- The resistance must be measured after the CAN junction connector CTR is disconnected.
- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D51-3 (CANH) - D51-14 (CANL)
P - W
Combination meter
Ignition switch off
108 to 132 Ω
D51-5 (CANH) - D51-16 (CANL)
SB - W
CAN junction connector CTR
Ignition switch off
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (Combination meter main wire)
B
NG (CAN junction connector main wire)
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR RH) |
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D51-1 (CANH) - D51-12 (CANL)
R - W
Steering angle sensor
Ignition switch off
1 MΩ or higher
D51-2 (CANH) - D51-13 (CANL)
BR - W
Power steering ECU
Ignition switch off
1 MΩ or higher
D51-4 (CANH) - D51-15 (CANL)
B - W
Skid control ECU
Ignition switch off
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (Steering angle sensor branch wire)
B
NG (Power steering ECU)
C
NG (Skid control ECU branch wire)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU MAIN WIRE) |
Disconnect the combination meter connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D51-3 (CANH) - D51-14 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 7. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR BRANCH WIRE) |
Disconnect the yaw rate sensor connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-2 (CANH) - D47-13 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 8. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
Disconnect the center airbag sensor assembly connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-3 (CANH) - D47-14 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 9. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
Disconnect the air conditioning amplifier connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-6 (CANH) - D47-17 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU BRANCH WIRE) |
Disconnect the main body ECU connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-8 (CANH) - D47-19 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 11. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE) |
Disconnect the steering angle sensor connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D51-1 (CANH) - D51-12 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 12. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU BRANCH WIRE) |
Disconnect the power steering ECU connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D51-2 (CANH) - D51-13 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 13. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE) |
Disconnect the skid control ECU connector.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D51-4 (CANH) - D51-15 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
