2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Lines for Short Circuit (RHD Models)

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

There may be a short circuit in the CAN main wire and/or CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short in CAN bus wire
  2. Skid control ECU
  3. Power steering ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. ECM
  7. Center airbag sensor assembly
  8. Air conditioning amplifier
  9. Combination meter
  10. Main body ECU
  11. CAN junction connector CTR
  12. CAN junction connector RH

WIRING DIAGRAM

C170474E03
C170477E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR CTR)
  1. Turn the ignition switch off.

  1. Disconnect the CAN junction connector CTR.

  1. Measure the resistance according to the value(s) in the table below.C170176E11

    Standard resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D47-1 (CANH) - D47-12 (CANL)
    SB - W
    CAN junction connector RH
    Ignition switch off
    108 to 132 Ω
    D47-4 (CANH) - D47-15 (CANL)
    L - W
    DLC3
    Ignition switch off
    1 MΩ or higher
    D47-5 (CANH) - D47-16 (CANL)
    R - W
    ECM
    Ignition switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (DLC3 branch wire)
    B
    NG (ECM main wire)
    C
    NG (CAN junction connector RH main wire)
    D



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3

C
Go to step 3

D
Go to step 4
A


2. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR CTR)

  1. Measure the resistance according to the value(s) in the table below.C170176E12

    Standard resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D47-2 (CANH) - D47-13 (CANL)
    G - W
    Yaw rate sensor
    Ignition switch off
    200 Ω or higher
    D47-3 (CANH) - D47-14 (CANL)
    Y - W
    Center airbag sensor assembly
    Ignition switch off
    200 Ω or higher
    D47-6 (CANH) - D47-17 (CANL)
    P - W
    Air conditioning amplifier
    Ignition switch off
    200 Ω or higher
    D47-8 (CANH) - D47-19 (CANL)
    GR - W
    Main body ECU
    Ignition switch off
    200 Ω or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Yaw rate sensor branch wire)
    B
    NG (Center airbag sensor assembly branch wire)
    C
    NG (Air conditioning amplifier branch wire)
    D
    NG (Main body ECU branch wire)
    E



B
Go to step 7

C
Go to step 8

D
Go to step 9

E
Go to step 10
A

REPLACE CAN JUNCTION CONNECTOR CTR

3. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)

  1. C228959E01
    Disconnect the ECM connector.

  1. C152875E70
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-5 (CANH) - D47-16 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)
OK

REPLACE ECM (Click here)

4. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR RH)
  1. Disconnect the CAN junction connector RH.

  1. Measure the resistance according to the value(s) in the table below.C170176E13

    HINT:
    The resistance must be measured after the CAN junction connector CTR is disconnected.


    Standard resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D51-3 (CANH) - D51-14 (CANL)
    P - W
    Combination meter
    Ignition switch off
    108 to 132 Ω
    D51-5 (CANH) - D51-16 (CANL)
    SB - W
    CAN junction connector CTR
    Ignition switch off
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Combination meter main wire)
    B
    NG (CAN junction connector main wire)
    C



B
Go to step 6

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - CAN JUNCTION CONNECTOR RH)
A


5. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR RH)

  1. Measure the resistance according to the value(s) in the table below.C170176E14

    Standard resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D51-1 (CANH) - D51-12 (CANL)
    R - W
    Steering angle sensor
    Ignition switch off
    200 Ω or higher
    D51-2 (CANH) - D51-13 (CANL)
    L - W
    Power steering ECU
    Ignition switch off
    200 Ω or higher
    D51-4 (CANH) - D51-15 (CANL)
    B - W
    Skid control ECU
    Ignition switch off
    200 Ω or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Steering angle sensor branch wire)
    B
    NG (Power steering ECU)
    C
    NG (Skid control ECU branch wire)
    D



B
Go to step 11

C
Go to step 12

D
Go to step 13
A

REPLACE CAN JUNCTION CONNECTOR RH

6. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU MAIN WIRE)

  1. C229505E01
    Disconnect the combination meter connector.

  1. C152875E73
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-3 (CANH) - D51-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ECU MAIN WIRE)
OK

REPLACE COMBINATION METER (Click here)

7. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR BRANCH WIRE)

  1. C165630E04
    Disconnect the yaw rate sensor connector.

  1. C152875E68
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-2 (CANH) - D47-13 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)
OK

REPLACE YAW RATE SENSOR (Click here)

8. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

  1. C131069E22
    Disconnect the center airbag sensor assembly connector.

  1. C152875E69
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-3 (CANH) - D47-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

9. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. C152868E06
    Disconnect the air conditioning amplifier connector.

  1. C152875E65
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-6 (CANH) - D47-17 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)

10. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU BRANCH WIRE)

  1. C195604E05
    Disconnect the main body ECU connector.

  1. C152875E72
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-8 (CANH) - D47-19 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU BRANCH WIRE)
OK

REPLACE MAIN BODY ECU

11. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C165753E03
    Disconnect the steering angle sensor connector.

  1. C152875E67
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-1 (CANH) - D51-12 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR BRANCH WIRE)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

12. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU BRANCH WIRE)

  1. C128052E11
    Disconnect the power steering ECU connector.

  1. C152875E77
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-2 (CANH) - D51-13 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU BRANCH WIRE)
OK

REPLACE POWER STEERING ECU (Click here)

13. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE)

  1. C156384E48
    Disconnect the skid control ECU connector.

  1. C152875E74
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-4 (CANH) - D51-15 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU BRANCH WIRE) (Click here)


← Check CAN Bus Lines for Short Circuit (RHD Models) (Aug 2008 – Jun 2010)Check CAN Bus Line for Short to +B (LHD Models) (May 2007 – Jul 2008) →