2007-2013 Highlander Kluger · Service Manual BRAKE

C0273 Open in ABS Motor Relay Circuit

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.
If the voltage supplied to the motor relay (+BM) is below the DTCs detection threshold due to low voltage from the battery or alternator, these DTCs may be stored.
DTC Code
DTC Detection Condition
Trouble Area
C0273
Either of the following is detected:
  1. All of the following conditions continue for 0.1 seconds or more.
    1. The IG1 terminal voltage is between 9.5 and 17.2 V.
    2. While initial check, or ABS, BA, TRC or VSC is operating.
    3. Relay contact remains open when the relay is ON.
  2. Both of the following conditions continue for 0.1 seconds or more.
    1. The IG1 terminal voltage is less than 9.5 V.
    2. Relay contact remains open when the relay is ON.
  1. Fusible link block (VSC NO. 1 fuse)
  2. ABS motor relay circuit
  3. Brake actuator assembly (ABS motor relay)
C0274
When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
  1. ABS motor relay circuit
  2. Brake actuator assembly (ABS motor relay)
C1361
Immediately after the ignition switch is turned on (IG), the relay contact is closed for 4 seconds when the motor fail safe relay is OFF.
  1. Fusible link block (VSC NO. 1 fuse)
  2. ABS motor fail safe relay circuit
  3. Brake actuator assembly (ABS motor fail safe relay)

WIRING DIAGRAM

C167211E01

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
When C1241 and/or C1417 is output together with C0273, C0274 and/or C1361, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (Click here, or Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operating sound of motor can be heard

  1. Check for operating sound of the ABS motor relay when operating it with the intelligent tester.

    Result:
    Result
    Proceed to
    Operating sound is not heard
    A
    Operating sound is heard
    B



B
Go to step 5
A


2. INSPECT VSC NO. 1 FUSE

  1. C169083E01
    Turn the ignition switch off.

  1. Remove the fusible link block from the engine room relay block.

  1. Check if the fusible link is melted.

    OK:
    The fusible link is not melted.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    VSC NO. 1 (50 A) fuse - Body ground
    Always
    Below 1 Ω



NG
REPLACE FUSIBLE LINK BLOCK (VSC NO. 1 FUSE)
OK


3. INSPECT SKID CONTROL ECU (+BM TERMINAL)

  1. C160263E38
    Install the fusible link block to the engine room relay block with the nut.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-24 (+BM) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)
OK


4. INSPECT SKID CONTROL ECU (GND2 TERMINAL)

  1. C160263E48
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-13 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


5. RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The ABS motor relay is in the brake actuator assembly.
Therefore, ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs (C0273, C0274 and C1361) are not output
    A
    DTCs (C0273, C0274 and/or C1361) are output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU with the ignition switch on (IG) and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
    4. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C0273 Open in ABS Motor Relay Circuit (+ C0274, C1361) (May 2007 – Jul 2008)C0273 Open in ABS Motor Relay Circuit (+ C0274, C1361) (from Jul 2010) →