P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Also covers:
- P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)
- P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)
- P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
Refer to DTC P0136 (Click here).- HINT:
- Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located furthest from the engine assembly.
- When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
- The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the B+ side of the circuit.
- Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located furthest from the engine assembly.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0037 P0057 |
Heated oxygen sensor heater current is less than 0.3 A (1 trip detection logic) |
|
| P0038 P0058 |
Heated oxygen sensor heater current is more than 2 A (1 trip detection logic) |
|
- HINT:
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that does not include cylinder No. 1.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor furthest away from the engine assembly.
- Bank 1 refers to the bank that includes cylinder No. 1.
WIRING DIAGRAM
Refer to DTC P0136 (Click here)INSPECTION PROCEDURE
- HINT:
- If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
- If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
| 1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Disconnect the heated oxygen sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- Bank 1:
Tester Connection
Condition
Specified Condition
2 (HT1B) - 1 (+B)
20°C (68°F)
11 to 16 Ω
2 (HT1B) - 3 (E2)
Always
10 kΩ or higher
- Bank 2:
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 4 (E2)
Always
10 kΩ or higher
Reconnect the heated oxygen sensor connector.
|
|
||||
| OK | |
| 2. INSPECT TERMINAL VOLTAGE (HEATER POWER SOURCE) |
Turn the ignition switch on (IG).

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- Bank 1:
Tester Connection
Switch Condition
Specified Condition
P1-1 (+B) - Body ground
Ignition switch on (IG)
9 to 14 V
- Bank 2:
Tester Connection
Switch Condition
Specified Condition
B38-2 (+B) - Body ground
Ignition switch on (IG)
9 to 14 V
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- Bank 1:
Tester Connection
Condition
Specified Condition
P1-2 (HT1B) - B1-1 (HT1B)
Always
Below 1 Ω
- Bank 2:
Tester Connection
Condition
Specified Condition
B38-1 (HT2B) - B2-5 (HT2B)
Always
Below 1 Ω
- Standard resistance (Check for short):
- Bank 1:
Tester Connection
Condition
Specified Condition
P1-2 (HT1B) or B1-1 (HT1B) - Body ground
Always
Below 1 Ω
- Bank 2:
Tester Connection
Condition
Specified Condition
B38-1 (HT2B) or B2-5 (HT2B) - Body ground
Always
Below 1 Ω
Reconnect the heated oxygen sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (EFI NO. 3 FUSE) |
Remove the EFI No. 3 fuse from engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
EFI No. 3 fuse
Always
Below 1 Ω
Reinstall the EFI No. 3 fuse.
|
|
||||
| OK | ||
| ||
