2007-2013 Highlander Kluger · Service Manual ENGINE

P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

Refer to DTC P0136 (Click here).

HINT:
  1. Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located furthest from the engine assembly.
  2. When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
  3. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the B+ side of the circuit.

A103832E71
DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
Heated oxygen sensor heater current is less than 0.3 A (1 trip detection logic)
  1. Open in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. EFI MAIN relay
  4. ECM
P0038
P0058
Heated oxygen sensor heater current is more than 2 A (1 trip detection logic)
  1. Short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. EFI MAIN relay
  4. ECM

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor furthest away from the engine assembly.


WIRING DIAGRAM

Refer to DTC P0136 (Click here)

INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A141063E06
    Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    2 (HT1B) - 1 (+B)
    20°C (68°F)
    11 to 16 Ω
    2 (HT1B) - 3 (E2)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E2)
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2. INSPECT TERMINAL VOLTAGE (HEATER POWER SOURCE)

  1. A168196E03
    Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-1 (+B) - Body ground
    Ignition switch on (IG)
    9 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B38-2 (+B) - Body ground
    Ignition switch on (IG)
    9 to 14 V



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

  1. A168197E02
    Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) - B1-1 (HT1B)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B38-1 (HT2B) - B2-5 (HT2B)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) or B1-1 (HT1B) - Body ground
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B38-1 (HT2B) or B2-5 (HT2B) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the heated oxygen sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. INSPECT FUSE (EFI NO. 3 FUSE)

  1. A168235E02
    Remove the EFI No. 3 fuse from engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI No. 3 fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI No. 3 fuse.



NG
REPLACE FUSE (EFI NO. 3 FUSE)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 3 FUSE - HEATED OXYGEN SENSOR)


← P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ P0038, P0057, P0058) (May 2007 – Jul 2008)P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ 5 more codes) (from Jul 2010) →