2007-2013 Highlander Kluger · Service Manual ENGINE

P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

CAUTION / NOTICE / HINT


DESCRIPTION

Refer to DTC P0136 (Click here).

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

A238849E05
DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
Heated oxygen sensor heater current is less than 0.3 A (1 trip detection logic)
  1. Open in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. ECM
P0038
P0058
Heated oxygen sensor heater current is more than specified value while the heater is operating (1 trip detection logic)
  1. Short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. ECM
P102D
P105D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic)
ECM

WIRING DIAGRAM

Refer to DTC P0136 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A141063E23
    Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    2 (HT1B) - 1 (+B)
    20°C (68°F)
    11 to 16 Ω
    2 (HT1B) - 3 (E2)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E2)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Component without harness connected
    (Heated Oxygen Sensor)

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2. CHECK TERMINAL VOLTAGE (+B TERMINAL OF HEATED OXYGEN SENSOR)

  1. A168196E11
    Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B38-2 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)

  1. Reconnect the heated oxygen sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - HEATED OXYGEN SENSOR)
OK


3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) - B47-12 (HT1B)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B38-1 (HT2B) - B47-13 (HT2B)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) or B47-12 (HT1B) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B38-1 (HT2B) or B47-13 (HT2B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the heated oxygen sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM)
OK


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes or more.

  1. When the vehicle stationary, depress the accelerator pedal and maintain an engine speed 3000 rpm for 1 minute.

  1. Idle the engine for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0037, P0038, P0057, P0058, P102D and/or P105D
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ P0038, P0057, P0058) (Aug 2008 – Jun 2010)P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (May 2007 – Jul 2008) →