2007-2013 Highlander Kluger · Service Manual ENGINE

P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

CAUTION / NOTICE / HINT

HINT:
  1. Although the DTC titles say the oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 (Click here).

HINT:
  1. When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A133850E27
DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air fuel ratio sensor heater (bank 1, 2, sensor 1) current less than 0.8 A (1 trip detection logic)
  1. Open in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (Bank 1, 2 sensor 1)
  3. A/F relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater (bank 1, 2, sensor 1) current fail
(1 trip detection logic)
  1. Short in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (Bank 1, 2 sensor 1)
  3. A/F relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is no operating
(1 trip detection logic)
ECM

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A192277E13
    Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.6 to 3.2 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.6 to 3.2 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Component without harness connected
    (Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2. CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

  1. A194092E23
    Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    B20-2 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B19-2 (+B) - Body ground
    Ignition switch on(IG)
    11 to 14 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR RELAY - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B47-17 (HA1A)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) - B47-19 (HA2A)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B47-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) or B47-19 (HA2A) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes or more.

  1. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute.

  1. Idle the engine for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0031, P0032, P0051, P0052, P101D and/or P103D
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

5. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (A/F RELAY)
  1. Inspect the A/F relay (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the engine room junction block assembly from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-2 (+B) - 2A-4
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-2 (+B) - 2A-4
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-2 (+B) or 2A-4 - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-2 (+B) or 2A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the engine room junction block assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - A/F RELAY)


← P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032, P0051, P0052) (Aug 2008 – Jun 2010)P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ P0038, P0057, P0058) (May 2007 – Jul 2008) →