2007-2013 Highlander Kluger · Service Manual ENGINE

Active Control Engine Mount System

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

DESCRIPTION

  1. LOCATION
    A168227E04
The active control engine mount system decreases engine vibration at low engine speed using the duty vacuum switching valve for active control engine mount. The duty vacuum switching valve for active control engine mount is controlled by a pulse signal transmitted to the duty vacuum switching valve for active control engine mount from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A207500E06

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK VACUUM HOSES

  1. A204508E01
    If the hose is damaged, replace the vacuum hose assembly.

  1. Check the air and vacuum hoses for looseness, disconnection and blockage.

    Text in Illustration 
    *1
    Engine
    *2
    Duty Vacuum Switching Valve
    *3
    Front Engine Mounting Insulator Assembly
    *4
    ECM
    *5
    Air Cleaner
    *6
    Vacuum Tank
    *7
    to No. 3 Intake Air Control Valve Assembly



NG
REPAIR OR REPLACE VACUUM HOSES
OK


2. CHECK VACUUM

  1. A242255
    Start the engine.

  1. Disconnect the vacuum hose from the vacuum tank on the air cleaner cap.

  1. Check that the disconnected port located on the vacuum tank applies suction to your finger.

    OK:
    Vacuum exists.

  1. Reconnect the vacuum hose.



NG
CHECK AND REPLACE VACUUM SOURCE AND HOSES
OK


3. INSPECT DUTY VACUUM SWITCHING VALVE (OPERATION)

  1. A052014E04
    Remove the duty vacuum switching valve for active control engine mount.

  1. Check operation of the duty vacuum switching valve when battery voltage is applied to the terminals of the duty vacuum switching valve connector.

    Battery voltage is not applied:
    The air from pipe G flows out through pipes E and H.

    Battery voltage is applied:
    The air from pipe F flows out through pipes E and H.

  1. Reinstall the duty vacuum switching valve for active control engine mount.



NG
REPLACE DUTY VACUUM SWITCHING VALVE (Click here)
OK


4. INSPECT DUTY VACUUM SWITCHING VALVE (RESISTANCE)

  1. A204509E06
    Disconnect the duty vacuum switching valve for active control engine mount connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    19 to 21 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Duty Vacuum Switching Valve)

  1. Reconnect the duty vacuum switching valve connector.



NG
REPLACE DUTY VACUUM SWITCHING VALVE (Click here)
OK


5. INSPECT FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

  1. A051989
    Disconnect the vacuum hose from the front engine mounting insulator assembly.

  1. Using a vacuum pump, apply vacuum of 80 kPa (600 mmHg, 23.622 in.Hg) and wait for 1 minute.

  1. Check that there is no change in the needle movement of the vacuum pump gauge.

  1. Check that there is no fluid leakage caused by a break in the diaphragm.

    OK:
    Vacuum does not leak.

  1. Reconnect the vacuum hose.



NG
REPLACE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (Click here)
OK


6. INSPECT DUTY VACUUM SWITCHING VALVE (POWER SOURCE VOLTAGE)

  1. A168214E04
    Disconnect the duty vacuum switching valve for active control engine mount connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B8-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Duty Vacuum Switching Valve)

  1. Reconnect the duty vacuum switching valve connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - DUTY VACUUM SWITCHING VALVE)
OK


7. CHECK HARNESS AND CONNECTOR (DUTY VACUUM SWITCHING VALVE - ECM)
  1. Disconnect the duty vacuum switching valve for active control engine mount connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B8-2 - B47-9 (ACM)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B8-2 or B47-9 (ACM) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the duty vacuum switching valve connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (DUTY VACUUM SWITCHING VALVE - ECM)
OK

REPLACE ECM (Click here)


← Active Control Engine Mount System (May 2007 – Jun 2010)ECM Power Source Circuit (May 2007 – Jul 2008) →