Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM
B2341 Sensor (Motor) Failure
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Also covers:
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
When the sliding roof drive gear sub-assembly (sliding roof control ECU) detects malfunctions in the motor, and the sliding roof operation is stopped, DTC B2341 is output. When the sliding roof drive gear sub-assembly (sliding roof control ECU) detects malfunctions in the gear, and the sliding roof operation is stopped, DTC B2344 is output.
DTC No.
DTC Detection Condition
Trouble Area
B2341
Sensor (motor) failure
Sliding roof drive gear sub-assembly (sliding roof control ECU)
Roof console box assembly (sliding roof switch assembly)
Wire harness
B2344
Position failure
Sliding roof drive gear sub-assembly (sliding roof control ECU)
Roof console box assembly (sliding roof switch assembly)
Wire harness
WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK SLIDING ROOF FUNCTION
Check the auto operation with the OPEN, DOWN, CLOSE and UP switches (Click here ).
OK:
Auto operation operates normally with OPEN, DOWN, CLOSE and UP switches.
NG
OK
2. RECHECK FOR DTC
Delete the DTCs (Click here ).
Recheck for DTCs (Click here ).
HINT:
If DTCs are detected frequently, replace the ECU.
OK:
DTC is not output.
NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) (Click here )
OK
3. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here ).
OK:
Sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized.
NG
OK
4. CHECK SLIDING ROOF FUNCTION
Check the auto operation with the OPEN, DOWN, CLOSE and UP switches (Click here ).
OK:
Auto operation operates normally with OPEN, DOWN, CLOSE and UP switches.
NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) (Click here )
OK
5. RECHECK FOR DTC
Delete the DTCs (Click here ).
Recheck for DTCs (Click here ).
HINT:
If DTCs are detected frequently, replace the ECU.
OK:
DTC is not output.
NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) (Click here )
OK
6. CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)
Disconnect the Q12 and Q1 connectors.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
Q12-2 (E) - Q1-2 (GND)
Always
Below 1 Ω
Q12-7 (OPN) - Q1-4 (OPN)
Always
Below 1 Ω
Q12-8 (DWN) - Q1-5 (DOWN)
Always
Below 1 Ω
Q12-9 (CLS) - Q1-3 (CLS)
Always
Below 1 Ω
Q12-10 (UP) - Q1-6 (UP)
Always
Below 1 Ω
Q1-3 (CLS) - Body ground
Always
10 kΩ or higher
Q1-4 (OPN) - Body ground
Always
10 kΩ or higher
Q1-2 (GND) - Body ground
Always
Below 1 Ω
Q1-5 (DOWN) - Body ground
Always
10 kΩ or higher
Q1-6 (UP) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)
Remove the roof console box assembly.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
Q1-3 (CLS) - Q1-2 (GND)
CLOSE
Below 100 Ω
Q1-4 (OPN) - Q1-2 (GND)
OPEN
Below 100 Ω
Q1-5 (DOWN) - Q1-2 (GND)
DOWN
Below 100 Ω
Q1-6 (UP) - Q1-2 (GND)
UP
Below 100 Ω
Q1-3 (CLS) - Q1-2 (GND)
OPEN
1 kΩ or higher
Q1-4 (OPN) - Q1-2 (GND)
CLOSE
1 kΩ or higher
Q1-5 (DOWN) - Q1-2 (GND)
UP
1 kΩ or higher
Q1-6 (UP) - Q1-2 (GND)
DOWN
1 kΩ or higher
NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) (Click here )
OK
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) (Click here )