C1403 Rear Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built from Jul 2010
Also covers:
- C1404 Rear Speed Sensor LH Malfunction
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1403 C1404 |
Any of the following is detected:
|
|
- HINT:
- DTC C1403 is for the rear speed sensor RH.
- DTC C1404 is for the rear speed sensor LH.
- DTC C1403 is for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK REAR SPEED SENSOR INSTALLATION |
Check the speed sensor installation (for 2WD).

- OK:
- There is no clearance between the sensor and the rear axle carrier.
Check the speed sensor installation (for 4WD).
- OK:
- There is no clearance between the sensor and the rear axle carrier.
- The installation nut is tightened properly.
- Torque:
- 8.5 N*m (87 kgf*cm, 75 in.*lbf)
- Result:
Result
Proceed to
OK (for 4WD)
A
OK (for 2WD)
B
NG (for 2WD)
C
NG (for 4WD)
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 3. CHECK REAR SPEED SENSOR ROTOR |
Remove the rear speed sensor rotor (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
- HINT:
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
|
|
||||
| OK | |
| 4. READ VALUE ON INTELLIGENT TESTER (REAR SPEED SENSOR) |
Install the rear speed sensor and the rear speed sensor rotor.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
RL Wheel Speed
RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
- Result:
Result
Proceed to
NG (for 4WD)
A
NG (for 2WD)
B
OK
C
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
|
|
||||
|
|
||||
| A | |
| 5. REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTCs (C1403 and C1404) are not output
A
DTCs (C1403 and/or C1404) are output
B
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
- HINT:
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
|
|
||||
| A | ||
| ||
