2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

B156B Multi-media Interface ECU Disconnected

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

The navigation receiver assembly and the multi-media interface ECU are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly and multi-media interface ECU, these DTCs will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B156B*1
When either condition below is met:
  1. Multi-media interface ECU is/was not connected while the ignition switch is/was ON or ACC.
  2. Communication between the master unit and the multi-media interface ECU is not possible when the engine is started.
  1. Multi-media interface ECU power source circuit
  2. AVC-LAN circuit between navigation receiver assembly and multi-media interface ECU
  3. Multi-media interface ECU
  4. Navigation receiver assembly
B156E
Within the time-out period, there was no response from the multi-media interface ECU to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E210099E02

INSPECTION PROCEDURE


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result:
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU POWER SOURCE)
  1. Disconnect the E25 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E25-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E25-12 (+B) - E25-7 (GND)
    Always
    11 to 14 V
    E25-11 (ACC) - E25-7 (GND)
    Ignition switch ACC
    11 to 14 V



NG
Go to step 7
OK


5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the E25 multi-media interface ECU connector.

  1. Disconnect the E23 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E25-9 (TX1+) - E23-9 (TXM+)
    Always
    Below 1 Ω
    E25-10 (TX1-) - E23-10 (TXM-)
    Always
    Below 1 Ω
    E25-9 (TX1+) - Body ground
    Always
    10 kΩ or higher
    E25-10 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE MULTI-MEDIA INTERFACE ECU
  1. Replace the multi-media interface ECU (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END

7. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the E23 navigation receiver assembly connector.

  1. Disconnect the E25 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E25-11 (ACC) - E23-11 (ACC)
    Always
    Below 1 Ω
    E25-12 (+B) - E23-12 (+B)
    Always
    Below 1 Ω
    E25-7 (GND) - E23-7 (GND)
    Always
    Below 1 Ω
    E25-11 (ACC) - Body ground
    Always
    10 kΩ or higher
    E25-12 (+B) - Body ground
    Always
    10 kΩ or higher
    E25-7 (GND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jul 2010)B1585 USB Media Malfunction (from Jul 2010) →