Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while it is operated in the direction of each arrow and turns off after being released. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM


E152497E09


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM


    E107091E12
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the Techstream main switch on.

  1. Select the following menu items: Powertrain / Cruise Control / Data List.

  1. Check the Data List for proper functioning of the cruise control main switch.

    ECM (Cruise control): 
    Techstream Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Main switch signal (Main CPU)/ON or OFF
    ON: Main switch on
    OFF: Main switch off
    -
    Cancel Switch
    CANCEL switch signal/ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    SET/COAST switch signal/ON or OFF
    ON: - SET switch on
    OFF: - SET switch off
    -
    RES/ACC Switch
    RES/ACC switch signal/ON or OFF
    ON: + RES switch on
    OFF: + RES switch off
    -

    OK:
    The display changes as shown above according to switch operation.
    Result 
    Result
    Proceed to
    OK
    A
    NG (All items are defective)
    B
    NG (1 to 3 items are defective)
    C



B
Go to step 2

C
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CRUISE CONTROL MAIN SWITCH
  1. Remove the cruise control main switch (Click here).



  1. Measure the resistance according to the value(s) in the table below.


    E106137E31


Standard resistance:

Tester Connection
Switch Condition
Specified Condition
A-1 (ECC) - A-3 (CCS)
Main Switch off*1
1 MΩ or higher
Main Switch on
Below 2.5 Ω
+ RES
235 to 245 Ω
- SET
617 to 643 Ω
CANCEL
1509 to 1571 Ω

*1: Lever is in the neutral position


NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
E103330E25
  1. Disconnect the z1 connector from the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - z1-3
    Always
    Below 1 Ω
    A-1 - z1-4
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SPIRAL CABLE
E144333E04

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    z1-3 (CCS) - D16-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z1-4 (ECC) - D16-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)


    E151265E01
  1. Disconnect the D36 connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-1 (CCS) - D36-2 (CCS)
    Always
    Below 1 Ω
    D36-2 (CCS) - Body ground
    Always
    10 kΩ or higher
    D16-2 (ECC) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)