SMART KEY SYSTEM > All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate |
| 1.READ VALUE ON TECHSTREAM (ENTRY CANCEL FUNCTION) |
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Data List.
Select Entry Cancel SW in the Data List and read the tester display.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Entry Cancel SW | Entry function cancel / ON or OFF | Mode status is displayed | - |
| Result | Proceed to |
| Entry function is ON | A |
| Entry function is OFF | B |
|
| ||||
| B | |
| 2.CHECK WAVE ENVIRONMENT |
Move the electrical key transmitter as described below and perform the operation inspection.
![]() |
Bring the electrical key transmitter near the driver door outside handle, and perform a front driver door entry lock and unlock operation check.
![]() |
Bring the electrical key transmitter near the front passenger door outside handle, and perform a front passenger door entry lock and unlock operation check.
![]() |
Bring the electrical key transmitter near the outside electrical key oscillator (back door), and perform an entry back door open and lock functions check.
| Result | Proceed to |
| Some operation checks are normal | A |
| All operation checks fail | B |
|
| ||||
| B | |
| 3.PERFORM KEY DIAGNOSTIC MODE INSPECTION |
![]() |
Diagnostic mode inspection (driver door outside handle oscillator)
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Driver Side.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
![]() |
Diagnostic mode inspection (front passenger door outside handle oscillator)
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Passenger Side.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
![]() |
Diagnostic mode inspection (indoor electrical key oscillator (front))
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Front Room.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
![]() |
Diagnostic mode inspection (indoor electrical key oscillator (rear))
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Rear Room.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
![]() |
Diagnostic mode inspection (indoor electrical key oscillator (luggage compartment))
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Back Door (inside).
When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.
![]() |
Diagnostic mode inspection (outside electrical key oscillator (back door))
Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus:
Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Back Door.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
| Result | Proceed to |
| Some diagnostic mode inspections fail (door) | A |
| Some diagnostic mode inspections fail (interior) | B |
| Some diagnostic mode inspections fail (back door) | C |
| All diagnostic mode inspections are normal | D |
| All diagnostic mode inspections fail | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| E | |
| 4.REPLACE ELECTRICAL KEY TRANSMITTER |
Replace the electrical key transmitter.
| NEXT | |
| 5.REGISTER ELECTRICAL KEY TRANSMITTER |
Register the electrical key transmitter (Click here).
| NEXT | |
| 6.CHECK ELECTRICAL KEY TRANSMITTER (OPERATION) |
Check that the entry functions operate normally.
|
| ||||
| OK | ||
| ||