TRANSFER CASE OIL SEAL > INSTALLATION |
| 1. INSTALL TRANSFER CASE OIL SEAL |
![]() |
Using SST, install a new transfer case oil seal to the transfer case at the position shown in the illustration.
Apply small amount of MP grease to the oil seal lip.
| 2. INSTALL CTR DIFFERENTIAL LOCK SLEEVE |
![]() |
Coat a new O-ring with hypoid gear oil.
Install the O-ring to the CTR differential lock sleeve.
![]() |
Using SST, install the CTR differential lock sleeve to the transfer case.
![]() |
Using snap ring pliers, install the shaft snap ring.
| 3. INSTALL TRANSFER ASSEMBLY |
![]() |
Apply sealant 1281 to the transaxle assembly and transfer assembly in a continuous bead of 1.2 mm diameter as shown in the illustration.
![]() |
Install the transfer assembly to the transaxle assembly with the 2 bolts and 6 nuts.
| 4. INSTALL AUTOMATIC TRANSAXLE WITH TRANSFER |
![]() |
Install the automatic transaxle with transfer to the engine with the 10 bolts.
![]() |
Apply a few drops of adhesive to the first 2 or 3 threads of the 6 torque converter clutch mounting bolts.
![]() |
Install the 6 torque converter clutch mounting bolts.
![]() |
Install the flywheel housing under cover to the automatic transaxle with the 2 bolts.
| 5. INSTALL TRANSFER STIFFENER PLATE RH |
![]() |
Install the transfer stiffener plate RH with 4 bolts to the transfer and engine mounting bracket RR.
| 6. CONNECT CONNECTORS |
![]() |
Connect the transmission wire connector.
Connect the park/neutral position switch connector.
Connect the 2 speed sensor connectors.
| 7. CONNECT WIRE HARNESS |
![]() |
Connect the wire harness with the bolt.
| 8. INSTALL WIRE HARNESS CLAMP |
![]() |
Install the 3 clamps and 3 bolts.
Connect the wire harness with the bolt.
| 9. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.
| 10. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD) |
| 11. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET |
![]() |
Install the transverse engine mount bracket with the 3 bolts.
| 12. INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY |
![]() |
Temporarily install the front engine mounting insulator assembly with the nut.
| 13. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR |
![]() |
Temporarily install the transverse engine mounting insulator with the nut.
| 14. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR |
![]() |
Temporarily install the transverse mounting insulator with the nut.
| 15. INSTALL FRONT FRAME ASSEMBLY |
Temporarily install the engine assembly with transaxle with the 9 nuts and 2 bolts.

![]() |
Tighten the 4 nuts.
![]() |
Tighten the 4 nuts.
![]() |
Tighten the 4 nuts.
![]() |
Tighten the 2 bolts.
![]() |
Connect the duty vacuum switching valve connector and clamp.
Install the 5 hole plugs.

| 16. INSTALL POWER STEERING LINK ASSEMBLY (for 4WD) |
![]() |
Install the power steering link assembly with the 2 bolts and 2 nuts.
| 17. INSTALL FRONT STABILIZER BAR |
| 18. REMOVE ENGINE HANGERS |
![]() |
Remove the 4 bolts and 2 engine hangers.
| 19. INSTALL MANIFOLD STAY |
![]() |
Install the bolt, nut and manifold stay.
| 20. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter assembly with the 2 bolts.
![]() |
Connect the starter connector.
Connect the starter wire with the nut and cover the nut with the cap.
| 21. INSTALL ENGINE WIRE |
Install the 3 bolts.

Connect the 2 clamps, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors, 3 injector assembly connectors and radio setting condenser connector.
Install the bolt and 2 nuts.

Connect the 2 clamps, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector connectors.
Connect the air fuel ratio sensor connector.
![]() |
Connect the 2 clamps, engine coolant temperature sensor connector and knock control sensor wire connector.
Install the ground cable bolt.
![]() |
Connect the purge VSV connector, air fuel ratio sensor connector and 2 clamps.
![]() |
Install the nut.
Connect the generator assembly connector and clamp.
![]() |
Connect the crankshaft position sensor connector and clamp.
![]() |
Connect the oil pressure switch assembly connector.
![]() |
Connect the oil pressure switch assembly cover.
| 22. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Oil Application Prohibited Bolt | ||
| Bolt for surge tank and intake manifold | ||
| Bolt for surge tank stay No. 1 and surge tank | ||
| Bolt for surge tank stay No. 1 and cylinder head cover | ||
| Bolt for throttle body bracket and surge tank | ||
| Bolt for throttle body bracket and cylinder head cover |
Install a new gasket to the intake air surge tank.
![]() |
Using a 5 mm hexagon socket wrench, install the 4 bolts and 2 nuts.
Install the throttle body bracket, No. 1 surge tank stay and 4 bolts.
![]() |
Connect the connector.
Connect the No. 1 ventilation hose.
![]() |
Install the clamp and connect the throttle with motor body assembly connector.
Connect the vapor feed hose.
Connect the 2 water by-pass hoses to the throttle with motor body assembly.
| 23. INSTALL VENTILATION HOSE |
![]() |
Using pliers, grip the claws of the 2 clips and slide the 2 clips to the intake air surge tank assembly and ventilation valve.
| 24. TEMPORARILY TIGHTEN COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Temporarily install the compressor and magnetic clutch with the bolts.
| 25. INSTALL COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Install the compressor and magnetic clutch with the 4 bolts.
![]() |
Engage each clamp.
Engage the clamp.
Connect the connector.
| 26. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Set the engine assembly with transaxle on the engine lifter.
Install the engine assembly to the vehicle.
![]() |
Install the frame side rail plates RH and LH with the 6 bolts and 2 nuts.
![]() |
Install the front suspension member rear braces RH and LH with the 6 bolts and 2 nuts.
| 27. RECONNECT SUCTION HOSE SUB-ASSEMBLY |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.
Install the O-ring onto the suction hose sub-assembly.
![]() |
Install the suction hose sub-assembly onto the compressor and magnetic clutch with the bolt.
| 28. RECONNECT DISCHARGE HOSE SUB-ASSEMBLY |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.
Install the O-ring onto the discharge hose sub-assembly.
![]() |
Install the discharge hose sub-assembly onto the compressor and magnetic clutch with the bolt.
| 29. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
![]() |
Install the bolt.
| 30. INSTALL FRONT AXLE ASSEMBLY LH |
![]() |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
| 31. INSTALL FRONT AXLE ASSEMBLY RH |
| 32. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH |
![]() |
Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.
| 33. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM RH |
| 34. CONNECT TIE ROD ASSEMBLY LH |
Connect the tie rod assembly LH to the steering knuckle with the nut.
Install a new cotter pin.
| 35. CONNECT TIE ROD ASSEMBLY RH |
| 36. INSTALL FRONT SPEED SENSOR LH |
![]() |
Install the resin clamp and front speed sensor with the bolt.
| 37. INSTALL FRONT SPEED SENSOR RH |
| 38. INSTALL FRONT AXLE HUB NUT LH |
Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.
![]() |
Using a socket wrench (30 mm), install a new axle hub nut.
Using a chisel and hammer, stake the front axle hub nut.
| 39. INSTALL FRONT AXLE HUB NUT RH |
| 40. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the front stabilizer link assembly to the front shock absorber with the nut.
| 41. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 42. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Install a new gasket to the front exhaust pipe assembly.
Install the front exhaust pipe assembly with 2 new nuts.
![]() |
Connect the heated oxygen sensor (for bank 2 sensor 2) connector.
| 43. INSTALL NO. 3 FRONT EXHAUST PIPE SUB-ASSEMBLY |
![]() |
Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.
Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.
![]() |
Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.
![]() |
Tighten the front exhaust pipe assembly bolt.
| 44. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the compression spring.
| Minimum | 41.5 mm (1.63 in.) |
![]() |
Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.
Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.
![]() |
Install the 2 compression springs and 2 bolts.
| 45. INSTALL TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the compression spring.
| Minimum | 40.5 mm (1.59 in.) |
![]() |
Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.
Connect the exhaust pipe support, and install the tail exhaust pipe assembly.
![]() |
Install the 2 compression springs and 2 bolts.
| 46. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.
![]() |
Remove SST from the transaxle.
Insert the yoke into the transaxle.
![]() |
Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.
![]() |
Tighten the 4 bolts.
| 47. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
![]() |
Remove the piece of cloth from the joint.
Using a hexagon wrench (6 mm), tighten the 6 bolts.
![]() |
With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.
Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

Check that the center line of the bracket is at the right angle in the shaft axial direction.
If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.
Turn the propeller shaft several times by hand to stabilize the center support bearings.
Using a jack, raise and lower the differential to stabilize the differential mounting cushion.
Remove the transfer dynamic damper.
Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).
Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

| Thickness mm (in.) | Thickness mm (in.) |
| 3.2 (0.126) | 11.0 (0.433) |
| 4.5 (0.177) | 13.5 (0.531) |
| 6.5 (0.256) | 15.5 (0.610) |
| 9.0 (0.354) | 17.5 (0.689) |
Install the transfer dynamic damper.
| 48. CONNECT ENGINE WIRE |
![]() |
Connect the 3 ECM connectors, 2 junction block connectors and clamp.
![]() |
Install the engine wire with the 2 nuts.
![]() |
Install the clip and 2 ground cables with the 2 bolts.
![]() |
Connect the heated oxygen sensor clamp and connector.
![]() |
Connect the engine wire clamp.
![]() |
Install the ground cable with the bolt.
![]() |
Connect the engine wire to the engine room relay block. Then, install it with the nut.
Connect the engine wire connector.
Install the No. 1 relay block cover.
| 49. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable to the control cable clamp.
![]() |
Install the transmission control cable assembly to the control shaft lever with the nut.
![]() |
Connect the transmission control cable assembly to the bracket with a new clip.
| 50. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push in the fuel tube connector to the fuel pipe until the fuel tube makes a "click" sound.
![]() |
Install the No. 1 fuel pipe clamp.
| 51. CONNECT OIL COOLER OUTLET HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the oil cooler outlet hose.
| 52. CONNECT OIL COOLER INLET HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the No. 2 oil cooler hose.
| 53. CONNECT HEATER WATER INLET HOSE B |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the heater water inlet hose B to water outlet.
| 54. CONNECT HEATER WATER OUTLET HOSE B |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the heater water outlet hose B to water inlet.
| 55. INSTALL NO. 1 RADIATOR HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 radiator hose to the water outlet.
Install the clamp with the air fuel ratio sensor connector.
| 56. INSTALL NO. 2 RADIATOR HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the No. 2 radiator outlet hose to the water inlet.
| 57. CONNECT UNION TO CHECK VALVE HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to connect the union to check valve hose to the intake air surge tank assembly.
| 58. CONNECT NO. 1 FUEL VAPOR FEED HOSE |
![]() |
Install the clamp and connect the No. 1 fuel vapor feed hose.
| 59. INSTALL ENGINE MOVING CONTROL ROD |
![]() |
Temporarily install the engine moving control rod with the 3 bolts.
First install bolts A, and then bolt B.
| 60. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Temporarily install the No. 2 engine mounting stay RH with the bolt.
Tighten the 2 nuts.
| 61. INSTALL RESERVOIR BRACKET |
![]() |
Install the reservoir bracket with the 2 bolts.
| 62. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
![]() |
Install the brake master cylinder reservoir assembly with the bolt.
Connect the level warning switch connector.
| 63. INSTALL AIR CLEANER BRACKET |
![]() |
Install the 2 bolts and air cleaner bracket.
| 64. INSTALL BATTERY |
![]() |
Install the battery tray and battery.
Install the battery clamp with the bolt and nut.
Install the positive battery terminal and nut.
Connect the negative battery terminal, and tighten the nut.
| 65. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 66. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the hose and connector.
| 67. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Install the air cleaner filter element sub-assembly.
| 68. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.
Install the air cleaner cap with the 2 bolts and clips
![]() |
Connect the 3 vacuum hoses.
![]() |
Connect the mass air flow meter connector.
Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.
| 69. INSTALL NO. 1 AIR CLEANER INLET |
![]() |
Install the No. 1 air cleaner inlet with the 2 bolts.
Connect the 2 vacuum hoses.
| 70. INSTALL NO. 2 AIR CLEANER INLET |
![]() |
Install the No. 2 air cleaner inlet with the 2 bolts.
Connect the 2 vacuum hoses and harness clamps.
| 71. CONNECT VACUUM HOSES |

| 72. INSTALL V-RIBBED BELT |
![]() |
Install the V-ribbed belt.
Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.
![]() |
If it is difficult to install the V-ribbed belt, perform the following procedure:
Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.
Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed tensioner assembly pulley.
After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.
| 73. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

![]() |
Install the 4 clips.
| 74. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 75. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 76. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 77. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 78. REMOVE FRONT WHEELS |
| 79. ADD ENGINE OIL |
Add clean engine oil and install the oil filler cap.
| Oil Grade | Oil Viscosity (SAE) |
| ILSAC multigrade engine oil | 5W-30 |
| Item | Standard Condition |
| Drain and refill with oil filter change | 6.1 liters (6.4 US qts, 5.4 lmp. qts) |
| Drain and refill without oil filter change | 5.7 liters (6.0 US qts, 5.0 lmp. qts) |
| Dry fill | 7.1 liters (7.5 US qts, 6.2 lmp. qts) |
| Item | Standard Condition |
| Drain and refill with oil filter change | 6.1 liters (6.4 US qts, 5.4 lmp. qts) |
| Drain and refill without oil filter change | 5.7 liters (6.0 US qts, 5.0 lmp. qts) |
| Dry fill | 6.8 liters (7.2 US qts, 6.0 lmp. qts) |
| 80. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug from the water inlet housing.
![]() |
Loosen the air drain plug at the top of the radiator 3 or 4 turns.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Condition | Specified Condition |
| w/ Rear Heater | 11.0 liters (11.6 US qts, 9.7 Imp. qts) |
| w/o Rear Heater | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Condition | Specified Condition |
| w/ Rear Heater | 11.7 liters (12.4 US qts, 10.3 Imp. qts) |
| w/o Rear Heater | 9.5 liters (10.1 US qts, 8.4 Imp. qts) |
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 81. INSTALL TRANSFER DRAIN PLUG |
![]() |
Install the transfer drain plug with a new drain gasket.
| 82. INSTALL NO.2 TRANSFER CASE PLUG |
Install the No. 2 transfer case plug with a new No. 2 gasket.
| 83. INSTALL NO.1 TRANSFER CASE PLUG |
Add oil up to 0 to 5 mm below the lower side of the plug hole.
Install the No. 1 transfer case plug with a new No. 1 gasket.
| 84. ADD AUTOMATIC TRANSAXLE FLUID |
| 85. CHECK AUTOMATIC TRANSAXLE FLUID |
Park the vehicle on a level surface and set the parking brake.
![]() |
With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.
Take out the dipstick and wipe it clean.
Put the dipstick back all the way.
Take out the dipstick again and check that the fluid level is within the HOT range.
If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.
| 86. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester main switch on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Check for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect Techstream from the DLC3.
| 87. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Check for engine oil leaks from the oil filter cap and oil filter drain plug.
Install the oil filter element service hole cover.
| 88. INSPECT FOR FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 89. INSPECT FOR EXHAUST GAS LEAK |
| 90. CHECK SHIFT LEVER POSITION |
When shifting from the P position to the R position with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.
Start the engine and make sure that the vehicle moves forward when shifting from the N position to the D position and moves rearward when shifting to the R position. If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.
| 91. CHECK AND ADJUST FRONT WHEEL ALIGNMENT |
| 92. CHECK IGNITION TIMING |
When using Techstream:
Check the ignition timing.
Connect Techstream to the DLC3.
Warm up the engine.
Turn the tester on.
Enter the following menu items: Powertrain / Engine and ECT / Data List / IGN Advance.
Read the value displayed on the tester.
![]() |
When not using Techstream:
Check the ignition timing.
Warm up the engine.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Remove the V-bank cover sub-assembly.
![]() |
Pull out the red lead wire harness.
Connect the tester terminal of the timing light to the red lead wire as shown in the illustration.
Check the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing at idle.
Confirm that the ignition timing advances immediately when the engine rpm is increased.
Remove the timing light from the engine.
| 93. CHECK ENGINE IDLE SPEED |
When using Techstream:
Check the idle speed.
Connect Techstream to the DLC3.
Warm up the engine.
Turn the tester on.
Enter the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the value displayed on the tester.
![]() |
When not using Techstream:
Check the idle speed.
Warm up the engine.
Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.
Check the idle speed.
| 94. CHECK CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.
Check CO/HC concentration at idle and/or 2500 rpm.
Check the air fuel ratio sensor and heated oxygen sensor operation.
See the following table for possible causes, and then inspect and repair if necessary.
| CO | HC | Problem | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 95. CHECK FUNCTION OF THROTTLE BODY ASSEMBLY |
Listen to the throttle control motor operating sounds.
Turn the ignition switch on (IG).
When pressing the accelerator pedal position sensor lever, listen to the running motor. Make sure that no friction noise comes from the motor.
If friction noise exists, replace the throttle body.
Inspect the throttle position sensor.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Check that the MIL turns off.
Turn the Techstream main switch on.
Select the menu items: Powertrain / Engine and ECT / Data List / Throttle Position.
Check the value of throttle valve angle is within the standard range below.
| 96. INSTALL FRONT FENDER APRON SEAL LH |
![]() |
Install the front fender apron seal LH with the 2 bolts and clip.
| 97. INSTALL FRONT FENDER APRON SEAL RH |
![]() |
Install the front fender apron seal RH with the 2 bolts and clip.
| 98. INSTALL FRONT FENDER LINER LH |
![]() |
Install the front fender liner LH with the 5 clips and 8 screws.
![]() |
Install 2 new grommets.
Using a 4 mm hexagon wrench, install the 2 screws.
![]() |
Install the screw and pin hold clip.
| 99. INSTALL FRONT FENDER LINER RH |
![]() |
Install the front fender liner RH with the 5 clips and 7 screws.
![]() |
Install 2 new grommets.
Using a 4 mm hexagon wrench, install the 2 screws.
![]() |
Install the screw and pin hold clip.
| 100. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the front fender side protector from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
![]() |
Clean the front fender moulding sub-assembly. (If reusing the front fender moulding sub-assembly)
Using a heat light, heat the front fender moulding sub-assembly.
Remove the front fender side protector from the front fender moulding sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Install a new front fender side protector to the the front fender moulding sub-assembly.
Install 2 new No. 4 clips on the front fender moulding sub-assembly.
Install a new pad on the front fender moulding sub-assembly.
![]() |
Install the front fender moulding sub-assembly.
Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.
Remove the release paper from the front fender moulding sub-assembly.
Engage the 3 clips and install the front fender moulding sub-assembly.
![]() |
Using a 4 mm hexagon wrench, install the screw.
Install the clip.
| 101. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH |
| 102. INSTALL FLOOR UNDER COVER LH |
| 103. INSTALL NO. 2 ENGINE UNDER COVER |
![]() |
Install the No. 2 engine under cover with the 2 bolts.
| 104. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the No. 1 engine under cover with the 6 bolts and 2 clips.
| 105. INSTALL ENGINE UNDER COVER ASSEMBLY |
![]() |
Install the engine under cover assembly with the 4 bolts and 5 clips.
![]() |
Install the engine under cover assembly RR with the 2 bolts.
| 106. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Fit the 3 retainers and install the V-bank cover.
| 107. CHECK ABS SPEED SENSOR SIGNAL |
| 108. RESET MEMORY |