Home › BRAKE › BRAKE CONTROL › BRAKE ACTUATOR

BRAKE ACTUATOR > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR


    C165836E02
  1. Install the brake actuator to the brake actuator bracket assembly with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not remove the hole plugs of a new brake actuator before connecting the 6 brake lines because the brake actuator is filled with brake fluid.
    2. Do not hold with the actuator by the connector.
    3. Tighten the 3 bolts in the order shown in the illustration.



    C165837
  1. Install the piping clamp to the brake actuator bracket assembly.



2. INSTALL BRAKE ACTUATOR WITH BRACKET


    C165835E01
  1. Install the brake actuator with bracket to the body with the 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Do not damage the brake lines or wire harness.
    2. Tighten the 3 bolts in the order shown in the illustration.



    C165838E01
  1. Temporarily tighten each brake line to the correct positions of the brake actuator with bracket as shown in the illustration.

    HINT:
    1. *1: To front wheel cylinder RH
    2. *2: To front wheel cylinder LH
    3. *3: To rear wheel cylinder RH
    4. *4: To rear wheel cylinder LH
    5. *5: From 1st of master cylinder
    6. *6: From 2nd of master cylinder



    C165840E01
  1. Using a union nut wrench (10 mm and 12 mm), fully tighten each brake line.

    Torque:
    Flare Nut A (M10) without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    Flare Nut A (M10) with union nut wrench:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Flare Nut B (M12) without union nut wrench:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    Flare Nut B (M12) with union nut wrench:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



    C165834
  1. Connect the brake actuator connector.

    NOTICE:
    1. Make sure that the connector is locked securely.
    2. Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.



    C165829
  1. Install the No. 1 cooler refrigerant suction tube to the 2 clamps.



    C165830
  1. Install the suction hose bracket to the brake actuator bracket assembly with the nut and bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    C165828
  1. Install the relay box.



3. FILL RESERVOIR WITH BRAKE FLUID


    C165889
  1. Fill the reservoir with brake fluid.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    Make sure that there is sufficient brake fluid in the reservoir.



4. BLEED BRAKE MASTER CYLINDER

NOTICE:
  1. If the master cylinder is reinstalled or if the reservoir becomes empty, bleed the master cylinder.
  2. To prevent brake fluid from adhering, cover the painted surfaces with a shop rag or a piece of cloth.



    C165942
  1. Using a union nut wrench (12 mm), disconnect the 2 brake lines from the master cylinder.



    C165891
  1. Slowly depress the brake pedal and hold it (*1).



    C165893
  1. Cover the 2 outer holes with fingers, and release the brake pedal (*2).

  1. Repeat (*1) and (*2) 3 or 4 times.



    C165943E01
  1. Using a union nut wrench (12 mm), connect the 2 brake lines to the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    with union nut wrench:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



5. BLEED BRAKE LINE

NOTICE:
  1. Bleed the brake line of the wheel farthest from the master cylinder first.
  2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.



    C165894
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (*3).



    C165895
  1. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*4).

  1. Repeat (*3) and (*4) until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure for each wheel to bleed the brake line.



6. BLEED BRAKE ACTUATOR

NOTICE:
After bleeding the brake system, if the specified height or feel of the brake pedal cannot be obtained, bleed the brake actuator assembly with Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the ignition switch off.

  1. Connect Techstream to the DLC3, and then turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Turn Techstream on and select "AIR BLEEDING" on the screen.

    NOTICE:
    1. Refer to the Techstream operator's manual for further details.
    2. Bleed the air by following the steps displayed on Techstream.



  1. Bleed the air according to "Step 1: Increase Line" on the Techstream display.

    NOTICE:
    1. Make sure that the master cylinder reservoir tank does not run out of brake fluid.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.




      C165894
    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).



    3. C165895
    4. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*6).

    5. Repeat (*5) and (*6) until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Repeat the above procedure for the rest of the wheels to bleed the brake lines.



  1. Bleed the suction line according to "Step 2: Inhalation Line" on the Techstream display.

    NOTICE:
    1. Bleed the suction line by following the steps displayed on Techstream.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.




      C165896
    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator assembly to bleed the air using Techstream (*7).

      NOTICE:
      1. During this step, be sure to release the brake pedal.
      2. The actuator operation stops automatically in 4 seconds.



    3. C165897
    4. Check that the actuator operation has stopped by referring to the Techstream display, and tighten the bleeder plug (*8).

    5. Repeat (*7) and (*8) until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. For the rest of the wheels, bleed the air in the same way as stated in the above procedure.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



  1. Bleed the pressure reduction line according to "Step 3: Decrease Line" on the Techstream display.

    NOTICE:
    1. Bleed the pressure reduction line by following the steps displayed on Techstream.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.




      C165898
    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (*9).

    3. While keeping the brake pedal fully depressed, operate the brake actuator assembly using Techstream.

      NOTICE:
      1. The actuator operation stops automatically in 4 seconds. When performing this procedure continuously, an interval of at least 20 seconds is required.
      2. After the operation is completed, the brake pedal goes down slightly. This is a normal phenomenon when the solenoid opens.
      3. During this procedure, the pedal seems heavy, but completely depress it so that the brake fluid comes out from the bleeder plug.
      4. Be sure to keep the brake pedal depressed. Never depress and release the pedal repeatedly.



    4. C165895
    5. Tighten the bleeder plug, and then release the brake pedal (*10).

    6. Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.

    7. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    8. Repeat the above procedures for the rest of the brakes to bleed the brake lines.



  1. Bleed the brake lines again according to "Step 4: Increase Line" on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on Techstream.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.




      C165898
    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).



    3. C165895
    4. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*12).

    5. Repeat (*11) and (*12) until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Repeat the above procedures for each brake to bleed the brake lines.

  1. Finish "AIR BLEEDING" on Techstream, and then turn off Techstream.

  1. Disconnect Techstream from the DLC3.

  1. Turn the ignition switch off.



7. INSPECT FLUID LEVEL IN RESERVOIR


    C165890E01
  1. Check the fluid level.
    If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



8. INSPECT FOR BRAKE FLUID LEAK


9. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (Click here)



11. INSPECT BRAKE ACTUATOR WITH TECHSTREAM

HINT:
(Click here).



12. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION

HINT:
(Click here).



13. CHECK AND CLEAR DTCS

HINT:
(Click here).