Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

The crankshaft position sensor (NE signal) consists of a magnet, iron core and pickup coil.
The NE signal plate (crankshaft position sensor plate) has 34 teeth and is installed on the crankshaft. The NE signal sensor generates 34 signals for each engine revolution. This sensor monitors a plate (timing rotor) located on the crankshaft timing pulley and is used by the ECM (included in the hybrid vehicle control ECU) to detect crankshaft angle and engine speed (RPM/NE). As the crankshaft timing pulley rotates through an engine revolution, this sensor communicates the rotation of the NE signal plate as a pulse signal to the ECM. Based on the signal, the ECM controls fuel injection duration and ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0335
No crankshaft position sensor signal to ECM (included in the hybrid vehicle control ECU) while engine running (engine rotating signal from hybrid vehicle control ECU) (2 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate
  4. Hybrid vehicle control ECU
Reference: Inspection using an oscilloscope.
A110929E01

HINT:
  1. The correct waveform is as shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.


Item
Content
Terminals
VV1+ - NE-
VV2+ - NE-
NE+ - NE-
Equipment Settings
5 V/Division, 20 ms/Division
Conditions
Cranking or idling

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine rotating, the ECM (included in the hybrid vehicle control ECU) interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, these DTCs are set 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check or rationality
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
4.7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Power switch
ON
Engine rotating signal from hybrid vehicle control ECU
Engine running

TYPICAL MALFUNCTION THRESHOLDS


Engine speed signal
No signal

WIRING DIAGRAM


A182713E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
  2. Check the engine speed. The engine speed can be checked by using the Techstream. To check, follow the operation below:
    1. Connect the Techstream to the DLC3.
    2. Put the engine in inspection mode (Click here).
    3. Start the engine.
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine rotating normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the crankshaft position sensor output voltage is insufficient.
  3. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT CRANKSHAFT POSITION SENSOR


    A178651E03
  1. Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    1850 to 2450 Ω

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)


    A178652E03
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B21-1 - B3-25 (NE+)
    Always
    Below 1 Ω
    B21-2 - B3-24 (NE-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B21-1 or B3-25 (NE+) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B3-24 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reconnect the crankshaft position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
OK


3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)


    BR03795E54
  1. Check the crankshaft position sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


4.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Remove the crankshaft position sensor plate (Click here).

  1. Check the teeth on the sensor plate.

    OK:
    Sensor plate does not have any crack or deformation.

  1. Reinstall the crankshaft position sensor plate (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)