DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 P2A03 |
|
|

| Related DTCs | P2A00: Air fuel ratio sensor (Bank 1) slow response P2A03: Air fuel ratio sensor (Bank 2) slow response |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Vehicle speed sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater - Sensor 1) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient engine coolant temperature for Closed Loop) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0451, P0452, P0453, P1451, P1452, P1453 (EVAP system) P0505 (Idle speed control) |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Engine RPM | Less than 4000 rpm |
| Fuel system status | Closed-loop |
| Idling | OFF |
| Fuel-cut | OFF |
| Engine load | 10 to 70% |
| Air fuel ratio sensor status | Activated |
| Air fuel ratio sensor malfunction (P2195 - P2198) | Not detected |
| Air fuel ratio sensor malfunction (P2237 - P2256) | Not detected |
| Response rate deterioration level | Less than 0.28 V |
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio sensor) | +25% | Rich | Less than 3.0 |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio sensor) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (Heated oxygen sensor) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (Heated oxygen sensor) | -12.5% | Lean | Less than 0.4 |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| P2A00 and/or P2A03 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the Techstream to the DLC3.
Put the engine in inspection mode (Click here).
Start the engine.
Turn the Techstream on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
On the Techstream, enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Snapshot / AFS Voltage B1S1 or AFS Voltage B2S1 and Engine Speed.
Check the the A/F sensor voltage three times, when the enigne is in each of the following conditions:
While idling (check for at least 30 seconds)
Fully depress the accelerator pedal and run the engine at 2500 rpm.
Accelerator pedal released.
| Condition | A/F Sensor Voltage Variation | Reference |
| (1) and (2) | Changes at approximately 3.3 V | Between 3.1 V and 3.5 V |
| (3) | Increases to 3.8 V or more | This occurs during engine deceleration when fuel-cut performed |

|
| ||||
| OK | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| No output | B |
|
| ||||
| A | |
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | |
| 8.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?.
|
| ||||
| YES | ||
| ||
| 9.INSPECT AIR FUEL RATIO SENSOR |
![]() |
Disconnect the air fuel ratio sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA1A) - 4 (A1A-) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HA2A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA2A) - 4 (A2A-) | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 10.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY |
Inspect the A/F relay (Click here).
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - HYBRID VEHICLE CONTROL ECU) |
![]() |
Disconnect the air fuel ratio sensor connectors.
Turn the power switch off.
Disconnect the hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B20-1 (HA1A) - B2-4 (HA1A) | Always | Below 1 Ω |
| B20-3 (A1A+) - B2-22 (A1A+) | Always | Below 1 Ω |
| B20-4 (A1A-) - B2-30 (A1A-) | Always | Below 1 Ω |
| B19-1 (HA2A) - B2-3 (HA2A) | Always | Below 1 Ω |
| B19-3 (A2A+) - B2-23 (A2A+) | Always | Below 1 Ω |
| B19-4 (A2A-) - B2-31 (A2A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B20- 1(HA1A) or B2-4 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B20-3 (A1A+) or B2-22 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B20-4 (A1A-) or B2-30 (A1A-) - Body ground | Always | 10 kΩ or higher |
| B19-1 (HA2A) or B2-3 (HA2A) - Body ground | Always | 10 kΩ or higher |
| B19-3 (A2A+) or B2-23 (A2A+) - Body ground | Always | 10 kΩ or higher |
| B19-4 (A2A-) or B2-31 (A2A-) - Body ground | Always | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connector.
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 12.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 13.CHECK PCV HOSE |
|
| ||||
| OK | |
| 14.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 15.INSPECT FUEL INJECTOR ASSEMBLY |
Check the injector injection (Click here).
|
| ||||
| OK | |
| 16.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | |
| 19.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?.
|
| ||||
| YES | ||
| ||