Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > MIL Circuit

for Preparation Click here


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM (included in the hybrid vehicle control ECU). When the power switch on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually. When the ignition switch is first turned on (IG), the MIL should be illuminated and should then turn off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the Techstream.

WIRING DIAGRAM


A182717E01


INSPECTION PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
  1. Turn the power switch on (IG).

  1. Check the illumination of the MIL.

    Result:

    Result
    Proceed to
    MIL remains illuminated (Even after power switch on (IG) and several seconds have passed, MIL still remains illuminated)
    A
    MIL remains off (Does not illuminate at all)
    B



B
Go to step 5
A


2.CHECK WHETHER MIL TURNS OFF
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Check if any DTCs have been stored. Note down any DTCs.

  1. Clear the DTCs (Click here).

  1. Check if the MIL goes off.

    Standard:
    MIL goes off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS 

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)


    A178722E02
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Turn the power switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
Go to step 4
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - HYBRID VEHICLE CONTROL ECU)


    A179787E01
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D35-14 (W) - E1-10 (CHK)
    Always
    Below 1 Ω

    Standard resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D35-14 (W) or E1-10 (CHK) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - HYBRID VEHICLE CONTROL ECU)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CHECK THAT ENGINE STARTS
  1. Turn the power switch on (IG).

  1. Switch the hybrid vehicle control ECU from normal mode to check mode (Click here).

  1. Start the engine.

    Result:
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The Techstream cannot communicate with the hybrid vehicle control ECU.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


6.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)


    A178722E02
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D35-14 (W) - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Reconnect the hybrid vehicle control ECU connector.



NG
Go to step 7
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - HYBRID VEHICLE CONTROL ECU)


    A179787E01
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D35-14 (W) - E1-10
    Always
    Below 1 Ω

    Standard resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D36-30 (W) or E1-10 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - HYBRID VEHICLE CONTROL ECU)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)