Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-214    Airbag ECU Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P3107-213 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
214
Open or short to +B in the communication circuit
  1. Wire harness or connector
  2. Center airbag sensor assembly
  3. Hybrid vehicle control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P3107-213 and DTC P31110-139 .

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (AIRBAG)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Body Electrical / SRS Airbag / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Airbag system DTCs are not output.
    A
    Airbag system DTCs are output.
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK CENTER AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)


    A138197E08
  1. Connect an oscilloscope between the center airbag sensor assembly terminals specified in the table below, and measure the waveform.
    Item
    Contents
    Terminal
    D30-14 (GSW2) - D30-25 (E1)
    Equipment Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Power switch on (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B



B
Go to step 6
A


3.CLEAR DTC (HV)
  1. Select the following menu items: Body Electrical / SRS Airbag / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Select the following menu items: Body Electrical / SRS Airbag / Trouble Codes.

  1. Clear DTCs.

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


4.CHECK DTC OUTPUT (HV)
  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-214 is not output.
    A
    P3107-214 is output again.
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


5.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems. (Click here)



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

6.CHECK CONNECTOR CONNECTION CONDITION (HV CONTROL ECU AND CENTER AIRBAG SENSOR ASSEMBLY CONNECTOR)


    A175549E01
  1. Check the connections of the hybrid vehicle control ECU and the center airbag sensor assembly connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the power switch off.

  1. Disconnect connector D35 from the hybrid vehicle control ECU.

  1. Disconnect connector D30 from the center airbag sensor assembly.

  1. Turn the power switch on (IG).



    A177972E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    D35-8 (ABFS) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU and the center airbag sensor assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-8 (ABFS) - D30-14 (GSW2)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-8 (ABFS) or D30-14 (GSW2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HYBRID VEHICLE CONTROL ECU
  1. Turn the power switch off.

  1. Disconnect the all connectors from the hybrid vehicle control ECU.



    A183481E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Tester Connection
    Switch Condition
    Specified Condition
    D35-8 (ABFS) - A43-2 (+B1)
    20°C (68°F)
    13 to 17 kΩ



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)