Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1231/31    Steering Angle Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU inputs steering angle sensor signals via the CAN communication. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126/63 (malfunction in communication with steering angle sensor) is output.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1231/31
-
Either of the following is detected:
  1. Steering angle sensor malfunction signal is received when data transmission is valid (internal malfunction is detected in sensor self check).
  2. A signal of +B open in steering angle sensor is received when communication with sensor is valid.
  1. Steering angle sensor
  2. Steering angle sensor circuit
  3. Steering angle sensor power supply
  4. Skid control ECU

WIRING DIAGRAM


C146553E04


INSPECTION PROCEDURE

HINT:
  1. When U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0126/63 first (Click here).
  2. When the speed sensor or the yaw rate and acceleration sensor are malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG) again and check that no CAN communication system DTC is output (Click here).

  1. Drive the vehicle and turn the steering wheel to the right and left at the speed of 35 km/h (22 mph) and check that no speed sensor and/or yaw rate sensor DTCs are output (Click here).

    Result:

    Result
    Proceed to
    No CAN communication system, speed sensor, yaw rate and acceleration sensor DTCs are output
    A
    CAN communication system DTC is output
    B
    Speed sensor and/or yaw rate sensor DTC is output
    C

    HINT:
    1. If there is a malfunction in the speed sensor or the yaw rate sensor, an abnormal value may be output although the steering angle sensor is normal.
    2. If speed sensor and yaw rate sensor DTCs are output simultaneously, repair these two sensors and inspect the steering angle sensor.



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2.INSPECT STEERING ANGLE SENSOR (POWER SOURCE TERMINAL)


    C156493E12
  1. Turn the power switch off.

  1. Remove the steering wheel and the column cover lower.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D14-4 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V
    D14-5 (BAT) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.INSPECT STEERING ANGLE SENSOR (GROUND TERMINAL)


    C156493E13
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D14-1 (ESS) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE STEERING ANGLE SENSOR (Click here)