Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0705-757    Transmission Range Sensor Circuit

DTC    P0705-758    Transmission Range Sensor Circuit

DTC    P0851-775    Park / Neutral Switch Input Circuit Low

for Preparation Click here


DESCRIPTION

The shift lever position sensor can send 8 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses the signals to detect the shift lever position (P, R, N, D, or B). The hybrid vehicle control ECU also uses this information to determine intended direction of travel (forward or reverse).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0705
757
Shift lever position sensor pattern problem
  1. Wire harness or connector
  2. Shift lever position sensor
  3. Hybrid vehicle control ECU
P0705
758
Shifting malfunction (open circuit in MJ)
P0851
775
N signal circuit malfunction

WIRING DIAGRAM


A183407E01


INSPECTION PROCEDURE

1.CLEAR DTC (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


2.READ VALUE USING TECHSTREAM (SHIFT POSITION)
  1. Select the following menu items: Powertrain / Hybrid Control / Data list / Shift Sensor SW-P, Shift Sensor SW-R, Shift Sensor SW-N, Shift Sensor SW-D, Shift Sensor SW-RV, Shift Sensor SW-FD, Shift Sensor SW-MJ.

  1. While slowly moving the shift lever from the P to B position, then back to P, read the data list (shift position) displayed on the Techstream.

    HINT:
    Be sure to move the shift lever slowly.


    Result:


    Shift Position
    ECU Data List
    P
    R
    N
    D
    B
    Shift Sensor SW-P
    ON
    OFF
    OFF
    OFF
    OFF
    Shift Sensor SW-R
    OFF
    ON
    OFF
    OFF
    OFF
    Shift Sensor SW-N
    OFF
    OFF
    ON
    OFF
    OFF
    Shift Sensor SW-D
    OFF
    OFF
    OFF
    ON
    OFF
    Shift Sensor SW-B
    OFF
    OFF
    OFF
    OFF
    ON
    Shift Sensor SW-RV
    OFF
    ON
    OFF
    OFF
    OFF
    Shift Sensor SW-FD
    OFF
    OFF
    OFF
    ON
    ON
    Shift Sensor SW-MJ
    ON
    ON
    ON
    ON
    ON

  1. Check if DTCs are output.

    OK:
    DTCs P0705-757, P0705-758, and P0851-775 are not output.



NG
Go to step 4
OK


3.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.CHECK HYBRID VEHICLE CONTROL ECU
  1. Turn the power switch on (IG).



    A174222E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B3-12 (P) - Body ground
    P position
    11 to 14 V
    B3-12 (P) - Body ground
    Any position except P position
    0 V
    B3-11 (R) - Body ground
    R position
    11 to 14 V
    B3-11 (R) - Body ground
    Any position except R position
    0 V
    B3-10 (N) - Body ground
    N position
    11 to 14 V
    B3-10 (N) - Body ground
    Any position except N position
    1 to 2.5 V
    B3-9 (D) - Body ground
    D position
    11 to 14 V
    B3-9 (D) - Body ground
    Any position except D position
    0 V
    B3-8 (B) - Body ground
    B position
    11 to 14 V
    B3-8 (B) - Body ground
    Any position except B position
    0 V
    B2-10 (MJ) - Body ground
    P, R, N, D, or B position
    11 to 14 V
    B2-11 (FD) - Body ground
    D or B position
    11 to 14 V
    B2-11 (FD) - Body ground
    Any position except D and B position
    0 V
    B2-12 (RV) - Body ground
    R position
    11 to 14 V
    B2-12 (RV) - Body ground
    Any position except R position
    0 V



NG
Go to step 5
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - BODY GROUND)
  1. Disconnect the shift lever position sensor connector.

  1. Turn the power switch on (IG).



    A174233E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B50-8 (+B) - Body ground
    Power switch on (IG)
    11 to 14 V

    NOTICE:
    Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT LEVER POSITION SENSOR)
  1. Turn the power switch off.

  1. Disconnect connectors B3 and B2 from the hybrid vehicle control ECU.

  1. Turn the power switch on (IG).



    A174232E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B3-12 (P) - Body ground
    Power switch on (IG)
    Below 1 V
    B3-11 (R) - Body ground
    Power switch on (IG)
    Below 1 V
    B3-10 (N) - Body ground
    Power switch on (IG)
    Below 1 V
    B3-9 (D) - Body ground
    Power switch on (IG)
    Below 1 V
    B3-8 (B) - Body ground
    Power switch on (IG)
    Below 1 V
    B2-10 (MJ) - Body ground
    Power switch on (IG)
    Below 1 V
    B2-11 (FD) - Body ground
    Power switch on (IG)
    Below 1 V
    B2-12 (RV) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the shift lever position sensor connector and hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    B3-12 (P) - B50-3 (P)
    Power switch off
    Below 1 Ω
    B3-11 (R) - B50-4 (R)
    Power switch off
    Below 1 Ω
    B3-10 (N) - B50-2 (N)
    Power switch off
    Below 1 Ω
    B3-9 (D) - B50-1 (D)
    Power switch off
    Below 1 Ω
    B3-8 (B) - B50-7 (B)
    Power switch off
    Below 1 Ω
    B2-10 (MJ) - B50-5 (MJ)
    Power switch off
    Below 1 Ω
    B2-11 (FD) - B50-6 (FD)
    Power switch off
    Below 1 Ω
    B2-12 (RV) - B50-9 (RV)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    B3-12 (P) or B50-3 (P) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B3-11 (R) or B50-4 (R) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B3-10 (N) or B50-2 (N) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B3-9 (D) or B50-1 (D) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B3-8 (B) or B50-7 (B) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B2-10 (MJ) or B50-5 (MJ) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B2-11 (FD) or B50-6 (FD) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    B2-12 (RV) or B50-9 (RV) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SHIFT LEVER POSITION SENSOR (Click here)