Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A38-257    Generator Temperature Sensor Circuit Low

DTC    P0A39-259    Generator Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A2C-247 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A38
257
GND short in generator temperature sensor circuit
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. Hybrid vehicle transaxle assembly (Generator temperature sensor)
P0A39
259
Open or +B short in generator temperature sensor circuit

HINT:
After confirming that DTC P0A38-257 or P0A39-259 is output, use Techstream to check "Motor Temp No1" in the hybrid vehicle control ECU data list.


Displayed Temperature
Malfunction
-58°F (-50°C)
Open circuit or short to +B
401°F (205°C)
Short to GND

WIRING DIAGRAM


A169640E13


INSPECTION PROCEDURE

1.CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A174883E01
  1. Check the connections of all hybrid vehicle control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.INSPECT HYBRID VEHICLE CONTROL ECU
  1. Turn the power switch on (IG).



    A174222E20
  1. Measure the voltage according to the value(s) in the table below.

    Result:

    Tester Connection
    Switch Condition
    Voltage
    Proceed to
    B1-22 (GMT) - B1-32 (GMTG)
    Power switch on (IG)
    11 to 14 V
    A
    Power switch on (IG)
    Approximately 0 V
    B



B
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (+B SHORT)


    A174441E05
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:

    Tester Connection
    Switch Condition
    Voltage
    Proceed to
    B1-22 (GMT) - B1-32 (GMTG)
    Power switch on (IG)
    11 to 14 V
    A
    Power switch on (IG)
    Approximately 0 V
    B

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing the inspection.



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


4.CHECK HARNESS AND CONNECTOR (+B SHORT)
  1. Remove the inverter with converter assembly (Click here).

  1. Disconnect the B1 connector from the hybrid vehicle control ECU.



    A174889
  1. Disconnect the B53 generator temperature sensor connector.

  1. Turn the power switch on (IG).



    A174451E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B53-4 (GMT) - Body ground
    Power switch on (IG)
    Approximately 0 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing the inspection.

    HINT:
    The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

5.INSPECT GENERATOR TEMPERATURE SENSOR


    A174441E06
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-22 (GMT) - B1-32 (GMTG)
    Thermistor temperature: 32°F (0°C)
    142.6 to 184.1 kΩ
    Thermistor temperature: 77°F (25°C)
    44.2 to 54.4 kΩ
    Thermistor temperature: 122°F (50°C)
    16.2 to 19.1 kΩ
    Thermistor temperature: 212°F (100°C)
    3.1 to 3.5 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-22 (GMT) or B1-32 (GMTG) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
Go to step 6
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - GENERATOR TEMPERATURE SENSOR)
  1. Remove the inverter with converter assembly (Click here).

  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Disconnect the B53 generator temperature sensor connector.



    A174451E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-22 (GMT) - B53-4 (GMT)
    Power switch off
    Below 1 Ω
    B1-32 (GMTG) - B53-9 (GMTG)
    Power switch off
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-22 (GMT) or B1-32 (GMTG) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    HINT:
    The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)