Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1391/69    Accumulator Leak Malfunction

for Preparation Click here


DESCRIPTION

The DTC is stored if an internal or external brake fluid leak is detected due to improper sealing in the brake actuator or brake booster pump. Internal leakage is suspected if the pump motor operates frequently without braking.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1391/69
591
Either of the following is detected:
  1. Before braking and when the pump motor is running, the accumulator pressure sensor input does not rise.
  2. Before braking and when the pump motor is not running, the accumulator pressure sensor input continues to fall at a greater rate than the standard value.
  1. Brake fluid leak
  2. Brake booster pump
  3. Brake actuator assembly

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK FOR FLUID LEAK


    C156531
  1. Check that there is no fluid leakage in the brake line between the brake actuator and the wheel cylinder which is indicated by DTCs.

  1. Check that the brake is not dragging.

    OK:
    There is no fluid leakage or dragging.



NG
REPAIR OR REPLACE APPLICABLE PART
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1391/69) is output
    A
    DTC (C1391/69) is not output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A


3.READ VALUE USING TECHSTREAM (PRESSURE SENSOR)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).


ABS / VSC / TRAC: 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Master Cylinder Sensor
Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
Master Cylinder Sensor2
Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
FR W/C Sensor
FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
FL W/C Sensor
FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
RR W/C Sensor
RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
RL W/C Sensor
RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
-
  1. Select the Active Test mode on the Techstream (Click here).

    HINT:
    The Active Test can be performed when the following conditions are met.
    1. ABS main relays 1 and 2 are on.
    2. Shift lever is in P.
    3. Parking brake is applied.
    4. Vehicle speed is 0 km/h (0 mph).


    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Solenoid (SMC1)
    Master cut solenoid (SMC1)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Solenoid (SMC2)
    Master cut solenoid (SMC2)
    Solenoid ON / OFF
    Operation sound of solenoid (clicking sound) can be heard
    ECB* Solenoid (SLRRL) Value Close
    Linear solenoid (SLRRL) valve
    Valve close ON / OFF
    -
    ECB* Solenoid (SLRRR) Value Close
    Linear solenoid (SLRRR) valve
    Valve close ON / OFF
    -
    *: Electronically Controlled Brake System

  1. Perform the Active Test of the solenoid using the Techstream.


C175403E01

  1. Check that the output value of each wheel cylinder does not increase.

    OK:
    The output value of each wheel cylinder does not increase.

    HINT:
    If any output value increases, there may be a brake fluid leak in the brake actuator.


    Result:

    Result
    Proceed to
    The output value of any wheel cylinder increases
    A
    The output values of all wheel cylinders do not increase
    B



B
REPLACE BRAKE BOOSTER PUMP (Click here)
A

REPLACE BRAKE ACTUATOR AND BRAKE BOOSTER PUMP ASSEMBLY (Click here)