Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

If the rear LH side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B177581E03


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH (REAR LH) (POWER SOURCE)


    B175982E03
  1. Disconnect the K2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    K2-3 (B) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW SWITCH (REAR LH)


    B164433E06
  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 (D) - 2 (SD)
UP
Below 1 Ω
3 (B) - 4 (U)
UP
Below 1 Ω
1 (D) - 2 (SD)
OFF
Below 1 Ω
4 (U) - 5 (SU)
OFF
Below 1 Ω
4 (U) - 5 (SU)
DOWN
Below 1 Ω
1 (D) - 3 (B)
DOWN
Below 1 Ω



NG
REPLACE POWER WINDOW SWITCH (REAR LH) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SWITCH (REAR LH) - MOTOR (REAR LH))


    B175983E05
  1. Disconnect the K2 and K3 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K2-4 (U) - K3-1 (U)
    Always
    Below 1 Ω
    K2-1 (D) - K3-2 (D)
    Always
    Below 1 Ω
    K2-4 (U) - Body ground
    Always
    10 kΩ or higher
    K2-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH)


  1. Check power window regulator motor operation.



      B164426E05
    1. Remove the power window regulator motor (Click here).

    2. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

      OK:
      Measurement Condition
      Specified Condition
      Battery negative (-) → Terminal 1
      Battery positive (+) → Terminal 2
      Motor gear rotates clockwise
      Battery negative (-) → Terminal 2
      Battery positive (+) → Terminal 1
      Motor gear rotates counterclockwise



  1. Check PTC operation:

    NOTICE:
    The work must be performed with the power window regulator and door glass installed on the vehicle.

    1. Install the power window regulator motor (Click here).



    2. B164428E23
    3. Connect an electrical tester DC 400 A probe to the wire harness of terminal 1.

      NOTICE:
      Match the arrow mark of the probe with the direction of the current flow.

    4. Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.

    5. Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

      Standard:
      4 to 90 seconds

    6. 60 seconds after the previous step, press the power window DOWN switch (rear LH side).

      OK:
      The rear LH side window goes down.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (REAR LH))


    B175975E02
  1. Disconnect the M1 and K2 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-12 (U) - K2-5 (SU)
    Always
    Below 1 Ω
    M1-13 (D) - K2-2 (SD)
    Always
    Below 1 Ω
    M1-12 (U) - Body ground
    Always
    10 kΩ or higher
    M1-13 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)