Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

The sound signals amplified by the stereo component amplifier are sent to the speakers from the stereo component amplifier through this circuit.
If there is a short in this circuit, the stereo component amplifier detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component or speakers.
If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E152199E04


E152200E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR


    E150794E01
  1. Disconnect the connectors shown in the illustration from the stereo component amplifier and speakers.

  1. Measure the resistance between each of the front No. 2 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-8 (FL+) - F3-1
    Always
    Below 1 Ω
    N16-7 (FL-) - F3-2
    Always
    Below 1 Ω
    N16-2 (FR+) - f1-1
    Always
    Below 1 Ω
    N16-6 (FR-) - f1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N15-2 (FL+) - H5-1
    Always
    Below 1 Ω
    N15-1 (FL-) - H5-2
    Always
    Below 1 Ω
    N15-9 (FR+) - G5-1
    Always
    Below 1 Ω
    N15-3 (FR-) - G5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-3 (RL+) - K1-1
    Always
    Below 1 Ω
    N16-9 (RL-) - K1-2
    Always
    Below 1 Ω
    N16-10 (RR+) - J1-1
    Always
    Below 1 Ω
    N16-4 (RR-) - J1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the stereo component speakers and the stereo component amplifier to check for an open circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N15-5 (WFL+) - T6-4 (WF+)
    Always
    Below 1 Ω
    N15-12 (WFL-) - T6-3 (WF-)
    Always
    Below 1 Ω
    N15-4 (WFR+) - T6-1 (WF+)
    Always
    Below 1 Ω
    N15-10 (WFR-) - T6-2 (WF-)
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    N16-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    N16-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    N16-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    N16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    N16-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    N16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    N16-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    N15-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    N15-1 (FL-) - Body ground
    Always
    10 kΩ or higher
    N15-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    N15-3 (FR-) - Body ground
    Always
    10 kΩ or higher
    N15-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    N15-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    N15-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    N15-10 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      1.8 to 2.6 Ω
      G5-1 - G5-2
      Always
      1.8 to 2.6 Ω

      NOTICE:
      The speaker should not be removed to check resistance.



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)  

4.INSPECT REAR SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      J1-1 - J1-2
      Always
      2.1 to 3.1 Ω
      K1-1 - K1-2
      Always
      2.1 to 3.1 Ω

      NOTICE:
      The speaker should not be removed to check resistance.



NG
REPLACE REAR SPEAKER (Click here)
OK


5.INSPECT STEREO COMPONENT SPEAKER


    E153727E01
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T6-1 (WF+) - T6-2 (WF-)
      Always
      1.6 to 2.4 Ω
      T6-4 (WF+) - T6-3 (WF-)
      Always
      1.6 to 2.4 Ω

      NOTICE:
      The speaker should not be removed to check resistance.



NG
REPLACE STEREO COMPONENT SPEAKER (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)