Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Hybrid System Indicator Malfunction

for Preparation Click here


DESCRIPTION

An ECON indicator light, variable economy zone display and EV drive mode indicator are adopted for this vehicle. In this circuit, the meter CPU receives the EV drive mode switch signal and pattern select switch signal from the hybrid vehicle control ECU via the CAN communication line (CAN No. 1 bus). The meter CPU controls the operation of the ECON indicator light, variable economy zone display and EV drive mode indicator as follows:
  1. ECON indicator light and variable economy zone display:
    An ECON indicator light and variable economy zone display are adopted to inform the driver of the fuel consumption while driving. Pressing the ECON switch located on the center console will switch between ECON mode and normal mode. When the meter CPU receives a signal from the ECON switch, it will illuminate the ECON indicator light to inform the drive that the vehicle is traveling in a mode that restricts excessive fuel consumption.
  2. EV drive indicator light
    EV drive mode is adopted for this vehicle to reduce noise and emission gas. While in EV drive mode, the EV drive indicator light illuminates to inform the drive that the vehicle is in a EV drive mode. While the EV drive mode operation conditions are met, pressing the EV drive mode switch (pattern select switch assembly) located on the center console will switch between EV drive mode and normal mode. When any of the previously met conditions become unsatisfied or if the EV drive mode operation conditions are not met, the EV drive indicator light will flash 3 times, a buzzer in the combination meter assembly will sound, and EV drive mode will be canceled. When the meter CPU receives an EV drive mode cancel signal, it will display an EV drive mode cancel warning on the multi-information display.

WIRING DIAGRAM


for ECON Indicator Light:

E156043E03


for EV Drive Indicator Light and Variable economy zone display:

E156043E04


INSPECTION PROCEDURE

HINT:
If there is an open or short in the EV drive mode switch circuit, or the pattern select switch circuit, the hybrid vehicle control ECU outputs DTCs. Perform troubleshooting with the "P310 Hybrid Control System" (Click here for EV drive mode switch circuit, Click here for Pattern select switch circuit).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check for the DTC (Click here).

    Result:

    Result
    Proceed to
    No CAN Communication DTC is output and EV drive mode indicator light has a malfunction.
    A
    No CAN Communication DTC is output and ECON indicator light or variable economy zone display has a malfunction.
    B
    CAN Communication DTC is output.
    C



B
Go to step 3

C
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (EV DRIVE MODE INDICATOR LIGHT)
  1. Connect Techstream to the DLC3.

  1. Power switch on (IG).

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the indicator light operation according to the values in the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EV Mode
    EV Mode indicator light
    EV Mode indicator light is OFF/ON
    Confirm that the vehicle is stopped, engine idling

    OK:
    Indicator light operation is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

Go to HYBRID CONTROL SYSTEM (Click here)  

3.PERFORM ACTIVE TEST USING TECHSTREAM (ECON INDICATOR LIGHT, VARIABLE ECONOMY ZONE DISPLAY)
  1. Connect Techstream to the DLC3.

  1. Power switch on (IG).

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the indicator light operation according to the values in the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. ECO
    Variable economy zone display
    Variable economy zone display is OFF/ON
    Confirm that the vehicle is stopped, engine idling
    Indicat. ECONO
    ECON indicator light
    ECON indicator light is OFF/ON
    Confirm that the vehicle is stopped, engine idling

    OK:
    Indicator light operation is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

Go to HYBRID CONTROL SYSTEM (Click here)