Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-213    Airbag ECU Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

  1. The hybrid vehicle control ECU detects a problem in the collision signal line from the center airbag sensor assembly and alerts the driver.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
213
GND short in communication circuit
  1. Wire harness or connector
  2. Center airbag sensor assembly
  3. Hybrid vehicle control ECU

WIRING DIAGRAM


A145954E07


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Body Electrical / SRS Airbag / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Airbag system DTCs are not output.
    A
    Airbag system DTCs are output.
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK CENTER AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)


    A138197E08
  1. Connect an oscilloscope between the center airbag sensor assembly terminals specified in the table below, and measure the waveform.
    Item
    Contents
    Terminal
    D30-14 (GSW2) - D30-25 (E1)
    Equipment Setting
    5 V/DIV, 500 ms/DIV
    Condition
    Power switch on (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B



B
Go to step 6
A


3.CLEAR DTC
  1. Select the following menu items: Powertrain / hybrid control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Select the following menu items: Powertrain / hybrid control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


4.CHECK DTC OUTPUT (HV)
  1. Select the following menu items: Powertrain / hybrid control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-213 is not output.
    A
    P3107-213 is output.
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


5.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems. (Click here)



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

6.CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn the power switch off.

  1. Disconnect connector D30 from the center airbag sensor assembly.



    A177971E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D30-14 (GSW2) - D30-25 (E1)
    Power switch off
    10 kΩ or higher



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect connector D35 from the hybrid vehicle control ECU.



    A177972E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-8 (ABFS) or D30-14 (GSW2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)