Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095459 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for driver door)

·

Main body ECU (multiplex network body ECU)

·

Wire harness or connector

·

P/W F/L fuse*1

·

P/W F/R fuse*2



*1: for LHD

*2: for RHD


WIRING DIAGRAM

for LHD


B365185
1.5,1.552 1.813,1.75 0.313,0.198 10 false 4D 1.5,1.719 3.104,2.208 1.604,0.49 10 false Instrument Panel Junction Block Assembly 0.302,1.896 0.615,2.094 0.313,0.198 10 false MB 0.302,2.052 1.458,2.667 1.156,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 1.094,0.906 1.708,1.104 0.615,0.198 10 false LIN2 2.458,0.771 2.771,0.969 0.313,0.198 10 false 25 1.49,0.771 1.802,0.969 0.313,0.198 10 false 16 0.698,3.385 2.469,3.573 1.771,0.188 10 false : LIN Communication Line 3.125,0.74 3.74,0.938 0.615,0.198 10 false 17 3.406,0.771 4.021,0.969 0.615,0.198 10 false LIN1 3.969,0.771 4.583,0.969 0.615,0.198 10 false LIN2 4.344,0.75 4.958,0.948 0.615,0.198 10 false 16 6.417,0.813 7,1.021 0.583,0.208 10 false P/W F/L 3.188,1.938 4.104,2.156 0.917,0.219 10 false I7 3.188,2.115 4.781,2.563 1.594,0.448 10 false Power Window Regulator Master Switch Assembly 5.042,1.906 5.5,2.104 0.458,0.198 10 false I4 5.042,2.073 7.01,2.531 1.969,0.458 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.188,0.927 5.802,1.125 0.615,0.198 10 false LIN 4.979,0.771 5.135,0.969 0.156,0.198 10 false 9 5.906,0.646 6.063,0.844 0.156,0.198 10 false B 5.719,1.292 6.052,1.542 0.333,0.25 10 false GND 6.135,0.542 6.292,0.74 0.156,0.198 10 false 2 6.125,1.188 6.281,1.385 0.156,0.198 10 false 1


for RHD


B365185
0.708,3.375 2.5,3.573 1.792,0.198 10 false : LIN Communication Line 0.292,2.01 1.438,2.625 1.146,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 0.292,1.854 0.604,2.052 0.313,0.198 10 false MB 1.479,1.583 1.792,1.781 0.313,0.198 10 false 4D 1.479,1.729 3.188,2.188 1.708,0.458 10 false Instrument Panel Junction Block Assembly 1.104,0.927 1.719,1.125 0.615,0.198 10 false LIN2 1.49,0.76 1.802,0.958 0.313,0.198 10 false 16 2.448,0.76 2.76,0.958 0.313,0.198 10 false 25 3.01,0.604 3.625,0.802 0.615,0.198 10 false 17*1 3.083,0.76 3.698,0.958 0.615,0.198 10 false 6*2 3.406,0.76 4.021,0.958 0.615,0.198 10 false LIN1 3.958,0.76 4.573,0.958 0.615,0.198 10 false LIN2 4.333,0.604 4.948,0.802 0.615,0.198 10 false 16*1 4.354,0.76 4.969,0.958 0.615,0.198 10 false 7*2 6.427,0.802 7.021,1.021 0.594,0.219 10 false P/W F/R 4.969,0.76 5.125,0.958 0.156,0.198 10 false 9 5.188,0.938 5.802,1.135 0.615,0.198 10 false LIN 5.917,0.646 6.073,0.844 0.156,0.198 10 false B 5.719,1.292 6.333,1.49 0.615,0.198 10 false GND 6.125,0.542 6.281,0.74 0.156,0.198 10 false 2 6.125,1.188 6.281,1.385 0.156,0.198 10 false 1 4.938,1.854 5.25,2.052 0.313,0.198 10 false H4 4.938,2.01 6.885,2.396 1.948,0.385 10 false Power Window Regulator Motor Assembly (for Driver Door) 3.104,1.938 3.948,2.156 0.844,0.219 10 false H7*1, H6*2 3.115,2.104 4.688,2.573 1.573,0.469 10 false Power Window Regulator Master Switch Assembly 3.156,2.948 6.75,3.188 3.594,0.24 10 false *1: for Models with Jam Protection Function on 4 Windows 3.156,3.25 6.75,3.49 3.594,0.24 10 false *2: for Models with Jam Protection Function on 2 Windows


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Models with Jam Protection Function on 4 Windows A
for Models with Jam Protection Function on 2 Windows B



A

2.CHECK DTC OUTPUT

B

8.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B2321 is output A
DTC B1206 and B2321 are output simultaneously B


HINT:

When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.



A

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B365181
1.156,1.854 1.49,1.854 1.49,1.854 1.49,1.354 false 2.083,1.854 1.667,1.854 1.667,1.854 1.667,1.354 false 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 0.844,1.781 1.458,1.979 0.615,0.198 10 false LIN1 2.146,1.771 2.76,1.969 0.615,0.198 10 false LIN2
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (LIN2) - 17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
a.

for LHD

i.

Disconnect the I4 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
I7-16 (LIN2) - I4-9 (LIN) Ignition switch off Below 1 Ω
I7-16 (LIN2) or I4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
H7-16 (LIN2) - H4-9 (LIN) Ignition switch off Below 1 Ω
H7-16 (LIN2) or H4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)
a.

for LHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I4-2 (B) - I4-1 (GND) Always 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-1 (GND) - Body ground Always Below 1 Ω




b.

for RHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H4-2 (B) - H4-1 (GND) Always 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-1 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

6.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

Replace the power window regulator motor assembly (for driver door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2321 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B2321 is output A
DTC B1206 and B2321 are output simultaneously B


HINT:

When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.



A

9.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

9.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B365182
1.063,0.281 1.396,0.281 1.396,0.281 1.396,1.031 false 1.885,0.281 1.552,0.281 1.552,0.281 1.552,1.031 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.74,0.208 1.052,0.406 0.313,0.198 10 false LIN2 1.958,0.198 2.271,0.396 0.313,0.198 10 false LIN1
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LIN2) - 6 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
a.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
H6-7 (LIN2) - H4-9 (LIN) Ignition switch off Below 1 Ω
H6-7 (LIN2) or H4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H4-2 (B) - H4-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

Replace the power window regulator motor assembly (for driver door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2321 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)