Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U023A Lost Communication with Front Camera Module No communication from the lane departure warning camera continues.
·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera


HINT:

Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.



HINT:

The diagnosis procedure is for when DTC U023A is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C294978
1.99,1.125 2.677,0.125 2.677,0.125 2.823,0.125 false 4.667,1.125 5.354,0.125 5.354,0.125 5.5,0.125 false 0.042,0.042 1.875,0.281 1.833,0.24 12 false Sub Bus 2: 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.385 5.104,5.583 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.063 6.115,5.417 1.854,0.354 10 false : CAN Branch Line (CANH) 4.26,5.396 6.104,5.667 1.844,0.271 10 false : CAN Branch Line (CANL) 0.625,4.083 2.458,4.281 1.833,0.198 10 false Trouble Area 1.688,3.958 2.354,4.198 0.667,0.24 10 false ECU-IG 2.833,3.813 3.146,4.01 0.313,0.198 10 false IGB 3.042,3.49 3.656,3.688 0.615,0.198 10 false CA1P 3.563,3.49 4.177,3.688 0.615,0.198 10 false CA1N 3.896,3.781 4.354,3.979 0.458,0.198 10 false GND 2.719,4.323 4.802,4.573 2.083,0.25 10 false Lane Departure Warning Camera 2.479,4.323 2.792,4.521 0.313,0.198 10 false S4 3.177,3.281 3.49,3.479 0.313,0.198 10 false 6 3.74,3.292 4.052,3.49 0.313,0.198 10 false 12 4.24,3.688 4.552,3.885 0.313,0.198 10 false 11 2.667,3.708 2.979,3.906 0.313,0.198 10 false 7 2.906,0.031 4.146,1.01 1.24,0.979 10 false No. 1 CAN Junction Connector 5.573,0.021 6.813,1 1.24,0.979 10 false No. 2 CAN Junction Connector 0.313,2.656 1.448,3.448 1.135,0.792 10 false Network Gateway ECU 5.677,2.656 7.115,2.906 1.438,0.25 10 false CAN Junction Terminal 0.708,2.021 1.479,2.219 0.771,0.198 10 false 120 Ω 6.167,2.021 6.938,2.219 0.771,0.198 10 false 120 Ω

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 52 seconds, and then drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Gateway > Trouble Codes
50001 150
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
DTC U1002 is not output from network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the S4 lane departure warning camera connector.


c.
C285244
1.521,0.25 1.927,0.49 0.406,0.24 2.729,1.917 2.5,1.917 2.5,1.917 2.177,1.438 true 2.719,0.573 2.552,0.573 2.552,0.573 2.177,1.125 true 0.198,0.125 0.51,0.281 0.313,0.156 10 false *a 2.781,0.479 3.396,0.677 0.615,0.198 10 false CA1P 2.792,1.823 3.406,2.021 0.615,0.198 10 false CA1N 1.635,0.271 2.25,0.469 0.615,0.198 10 false S4
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-6 (CA1P) - S4-12 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (LANE DEPARTURE WARNING CAMERA)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285244
1.469,0.24 1.875,0.479 0.406,0.24 2.469,1.854 2.313,1.854 2.313,1.854 2.021,1.448 true 0.198,0.125 0.51,0.281 0.313,0.156 10 false *a 2.51,1.76 3.125,1.958 0.615,0.198 10 false GND 1.604,0.271 2.219,0.469 0.615,0.198 10 false S4
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-11 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C285244
1.469,0.24 1.875,0.479 0.406,0.24 1.333,1.448 1.219,1.854 1.219,1.854 1.052,1.854 true 0.198,0.125 0.51,0.281 0.313,0.156 10 false *a 0.792,1.76 1.406,1.958 0.615,0.198 10 false IGB 1.583,0.26 2.198,0.458 0.615,0.198 10 false S4
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S4-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)