Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Steering sensor

·

Airbag sensor assembly

·

ECM

·

Skid control ECU (brake actuator assembly)

·

Air conditioning amplifier assembly

·

Network gateway ECU*1

·

4WD ECU assembly*2

·

Navigation receiver assembly*3

·

Radio and display receiver assembly*4

·

Clearance warning ECU assembly*5

·

Headlight leveling ECU assembly*6

·

Certification ECU (smart key ECU assembly)*7

·

No. 3 CAN junction connector

·

No. 4 CAN junction connector



·

*1: w/ Blind Spot Monitor System or Parking Assist Monitor System

·

*2: for AWD

·

*3: for Navigation Receiver Type

·

*4: for Radio and Display Type

·

*5: w/ Toyota Parking Assist-sensor System

·

*6: w/ Automatic Headlight Beam Level Control System

·

*7: w/ Smart Entry and Start System


WIRING DIAGRAM

C295258
0.094,0.052 1.719,0.594 1.625,0.542 12 false V Bus: 5.625,0.063 6.958,0.417 1.333,0.354 10 false x: Suspected Area 3.479,0.406 4.25,0.604 0.771,0.198 10 false 120 Ω 4.104,1.031 4.719,1.229 0.615,0.198 10 false CANH 2.802,1.042 3.417,1.24 0.615,0.198 10 false CANL 0.031,1.323 2.813,1.552 2.781,0.229 10 false *1: w/ Toyota Parking Assist-sensor System 4.625,0.594 5.083,0.792 0.458,0.198 10 false A43 4.938,0.594 5.396,0.792 0.458,0.198 10 false ECM 4.083,1.271 4.396,1.469 0.313,0.198 10 false 13 3.021,1.281 3.333,1.479 0.313,0.198 10 false 26 4.115,1.615 4.271,1.813 0.156,0.198 10 false B 3.01,1.635 3.167,1.833 0.156,0.198 10 false W 4.094,1.979 4.25,2.177 0.156,0.198 10 false 2 3.052,2 3.365,2.198 0.313,0.198 10 false 12 2.792,2.26 2.948,2.458 0.156,0.198 10 false 3 2.74,2.896 3.052,3.094 0.313,0.198 10 false 13 1.969,2.198 2.229,2.438 0.26,0.24 10 false BE 1.99,2.948 2.146,3.146 0.156,0.198 10 false W 1.531,2.875 1.938,3.25 0.406,0.375 10 false 12 1.531,2.281 1.76,2.521 0.229,0.24 10 false 11 1.021,2.271 1.635,2.469 0.615,0.198 10 false CANH 1.031,2.865 1.646,3.063 0.615,0.198 10 false CANL 0.063,3.115 0.521,3.313 0.458,0.198 10 false F80 0.385,3.125 1.958,4 1.573,0.875 10 false Air Conditioning Amplifier Assembly 4.385,2.375 4.813,2.625 0.427,0.25 10 false F102 4.75,2.375 6.781,2.719 2.031,0.344 10 false No. 3 CAN Junction Connector 4.396,3.188 4.552,3.385 0.156,0.198 10 false 6 4.375,3.813 4.688,4.01 0.313,0.198 10 false 16 5.208,3.135 5.365,3.333 0.156,0.198 10 false R 5.188,3.896 5.344,4.094 0.156,0.198 10 false W 5.594,3.177 5.906,3.375 0.313,0.198 10 false 14 5.594,3.823 5.906,4.021 0.313,0.198 10 false 13 5.865,3.219 6.479,3.417 0.615,0.198 10 false CANH 5.865,3.833 6.479,4.031 0.615,0.198 10 false CANL 5.542,4.063 5.854,4.26 0.313,0.198 10 false F19 5.854,4.063 7.146,5.385 1.292,1.323 10 false Main Body ECU (Multiplex Network Body ECU) 2.792,4.125 2.948,4.323 0.156,0.198 10 false 5 2.74,4.771 3.052,4.969 0.313,0.198 10 false 15 1.99,4.823 2.146,5.021 0.156,0.198 10 false W 1.99,4.031 2.302,4.229 0.313,0.198 10 false LG 1.531,4.125 1.844,4.323 0.313,0.198 10 false 17 1.531,4.74 1.844,4.938 0.313,0.198 10 false 18 1.26,4.115 1.573,4.313 0.313,0.198 10 false R1 1.25,4.74 1.563,4.938 0.313,0.198 10 false R2 0.031,4.99 0.49,5.188 0.458,0.198 10 false F87 0.344,4.99 1.531,5.771 1.188,0.781 10 false Clearance Warning ECU Assembly*1 2.802,5.896 2.958,6.094 0.156,0.198 10 false 4 2.74,6.51 3.052,6.708 0.313,0.198 10 false 14 2.01,5.823 2.167,6.021 0.156,0.198 10 false Y 1.99,6.573 2.146,6.771 0.156,0.198 10 false W 1.542,5.906 1.854,6.104 0.313,0.198 10 false 13 1.552,6.552 1.865,6.75 0.313,0.198 10 false 22 1.042,5.906 1.656,6.104 0.615,0.198 10 false CANH 1.052,6.542 1.667,6.74 0.615,0.198 10 false CANL 0.042,6.771 0.5,6.969 0.458,0.198 10 false F38 0.365,6.771 1.927,7.51 1.563,0.74 10 false Airbag Sensor Assembly 4.406,5.188 4.563,5.385 0.156,0.198 10 false 7 4.385,5.844 4.698,6.042 0.313,0.198 10 false 17 5.188,5.156 5.344,5.354 0.156,0.198 10 false G 5.177,5.917 5.333,6.115 0.156,0.198 10 false W 5.635,5.229 5.948,5.427 0.313,0.198 10 false 7 5.635,5.833 5.948,6.031 0.313,0.198 10 false 8 5.854,5.198 6.469,5.396 0.615,0.198 10 false CANH 5.865,5.844 6.479,6.042 0.615,0.198 10 false CANL 5.521,6.083 5.979,6.281 0.458,0.198 10 false F13 5.844,6.083 6.917,7.146 1.073,1.063 10 false Certification ECU (Smart Key ECU Assembly)*2 0.031,1.615 5.385,1.813 5.354,0.198 10 false *2: w/ Smart Entry and Start System 0.844,8.042 4.823,8.24 3.979,0.198 10 false : CAN Main Bus Line (CANH) 0.844,8.448 4.823,8.646 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.958,8.021 5.677,8.25 1.719,0.229 10 false : CAN Branch Line (CANH) 3.948,8.427 5.729,8.667 1.781,0.24 10 false : CAN Branch Line (CANL)

C295259
0.083,0.073 3.021,0.313 2.938,0.24 12 false V Bus: 5.177,0.031 6.583,0.438 1.406,0.406 10 false x: Suspected Area 4.563,3.802 5.042,4.031 0.479,0.229 10 false F102 4.958,3.802 6.979,4.125 2.021,0.323 10 false No. 3 CAN Junction Connector 4.542,2.125 4.698,2.323 0.156,0.198 10 false 9 4.5,2.729 4.813,2.927 0.313,0.198 10 false 19 5.24,2.073 5.552,2.271 0.313,0.198 10 false GR 5.271,2.802 5.427,3 0.156,0.198 10 false W 5.771,2.104 5.927,2.302 0.156,0.198 10 false 6 5.781,2.76 5.938,2.958 0.156,0.198 10 false 7 5.979,2.104 6.594,2.302 0.615,0.198 10 false CANH 5.99,2.729 6.604,2.927 0.615,0.198 10 false CANL 5.583,2.979 6.042,3.177 0.458,0.198 10 false A67 5.917,2.969 7.042,3.531 1.125,0.563 10 false Headlight Leveling ECU Assembly*3 2.927,0.74 3.083,0.938 0.156,0.198 10 false 8 2.885,1.344 3.198,1.542 0.313,0.198 10 false 18 2.24,0.698 2.396,0.896 0.156,0.198 10 false L 2.208,1.438 2.365,1.635 0.156,0.198 10 false W 1.26,0.75 1.417,0.948 0.156,0.198 10 false 6 1.26,1.375 1.417,1.573 0.156,0.198 10 false 5 0.75,0.76 1.365,0.958 0.615,0.198 10 false CANH 0.771,1.354 1.385,1.552 0.615,0.198 10 false CANL 0.042,1.625 0.5,1.823 0.458,0.198 10 false F14 0.354,1.625 1.865,1.979 1.51,0.354 10 false 4WD ECU Assembly*1 2.844,3.167 3.156,3.365 0.313,0.198 10 false 10 2.854,3.865 3.167,4.063 0.313,0.198 10 false 20 2.167,3.094 2.323,3.292 0.156,0.198 10 false P 2.156,3.885 2.313,4.083 0.156,0.198 10 false W 1.25,3.167 1.563,3.365 0.313,0.198 10 false 16 1.25,3.823 1.563,4.021 0.313,0.198 10 false 15 0.781,3.198 1.396,3.396 0.615,0.198 10 false CA1H 0.781,3.813 1.396,4.01 0.615,0.198 10 false CA1L 0.031,4.052 0.49,4.25 0.458,0.198 10 false F85 0.333,4.052 2.333,4.646 2,0.594 10 false Network Gateway ECU*2 4.229,4.49 4.385,4.688 0.156,0.198 10 false 1 3.167,4.479 3.479,4.677 0.313,0.198 10 false 11 3.188,5.375 3.5,5.573 0.313,0.198 10 false 11 4.229,5.365 4.385,5.563 0.156,0.198 10 false 1 4.24,4.917 4.552,5.115 0.313,0.198 10 false BR 3.115,4.906 3.271,5.104 0.156,0.198 10 false W 2.917,5.635 3.073,5.833 0.156,0.198 10 false 4 2.875,6.292 3.188,6.49 0.313,0.198 10 false 14 2.208,5.583 2.521,5.781 0.313,0.198 10 false BE 2.208,6.354 2.365,6.552 0.156,0.198 10 false W 1.271,5.646 1.427,5.844 0.156,0.198 10 false 3 1.271,6.313 1.427,6.51 0.156,0.198 10 false 2 0.76,5.646 1.375,5.844 0.615,0.198 10 false CANH 0.771,6.271 1.385,6.469 0.615,0.198 10 false CANL 0.031,6.531 0.49,6.729 0.458,0.198 10 false F58 0.354,6.531 2.646,6.729 2.292,0.198 10 false Steering Sensor 4.521,6.76 4.677,6.958 0.156,0.198 10 false 3 4.49,7.406 4.802,7.604 0.313,0.198 10 false 13 5.333,6.719 5.49,6.917 0.156,0.198 10 false V 5.313,7.479 5.469,7.677 0.156,0.198 10 false W 5.792,6.771 5.948,6.969 0.156,0.198 10 false 6 5.938,7.427 6.25,7.625 0.313,0.198 10 false 14 6.177,7.458 6.49,7.656 0.313,0.198 10 false F25 6.479,7.458 7.094,7.656 0.615,0.198 10 false DLC3 6.031,6.885 6.646,7.083 0.615,0.198 10 false CANH 6.198,7.229 6.813,7.427 0.615,0.198 10 false CANL 4.521,6 5.042,6.24 0.521,0.24 10 false F103 4.906,6 6.927,6.323 2.021,0.323 10 false No. 4 CAN Junction Connector 0.792,9.042 4.771,9.24 3.979,0.198 10 false : CAN Main Bus Line (CANH) 0.792,9.417 4.771,9.615 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.958,9.063 5.896,9.344 1.938,0.281 10 false : CAN Branch Line (CANH) 3.958,9.448 5.781,9.76 1.823,0.313 10 false : CAN Branch Line (CANL) 0.208,7.25 1.896,7.448 1.688,0.198 10 false *1: for AWD 0.208,7.573 2.302,8.135 2.094,0.563 10 false *2: w/ Blind Spot Monitor System or Parking Assist Monitor System 0.208,8.208 2.292,8.896 2.083,0.688 10 false *3: w/ Automatic Headlight Beam Level Control System

C298600
3.948,8.01 5.99,8.26 2.042,0.25 10 false : CAN Branch Line (CANH) 0.771,8 2.813,8.25 2.042,0.25 10 false : CAN Main Bus Line (CANH) 0.792,8.375 2.833,8.625 2.042,0.25 10 false : CAN Main Bus Line (CANL) 3.938,8.385 5.979,8.635 2.042,0.25 10 false : CAN Branch Line (CANL) 0.094,0.063 1.198,0.302 1.104,0.24 12 false V Bus: 4.781,7.125 5.24,7.323 0.458,0.198 10 false F22 0.073,4.385 0.323,4.604 0.25,0.219 10 false p1 5.573,3.104 6.031,3.302 0.458,0.198 10 false F71 0.073,1.542 0.417,1.729 0.344,0.188 10 false A47 0.375,1.542 1.927,2.031 1.552,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 0.292,4.385 1.604,4.865 1.313,0.479 10 false Power Steering ECU Assembly 0.76,0.667 1.271,0.875 0.51,0.208 10 false CANH 4.25,6.844 4.75,7.063 0.5,0.219 10 false CANH 0.802,1.021 1.302,1.208 0.5,0.188 10 false CANL 0.771,3.521 1.24,3.719 0.469,0.198 10 false CANH 5.969,4.24 6.438,4.438 0.469,0.198 10 false CANH 5.969,2.26 6.417,2.49 0.448,0.229 10 false CANH 5.969,2.625 6.406,2.813 0.438,0.188 10 false CANL 5.969,4.615 6.458,4.813 0.49,0.198 10 false CANL 2.927,6.854 3.365,7.042 0.438,0.188 10 false CANL 0.802,3.875 1.229,4.073 0.427,0.198 10 false CANL 1.25,1.021 1.563,1.219 0.313,0.198 10 false 14 2.198,0.583 2.51,0.781 0.313,0.198 10 false GR 2.896,4.115 3.208,4.313 0.313,0.198 10 false 15 2.875,1.271 3.188,1.469 0.313,0.198 10 false 12 1.26,0.656 1.573,0.854 0.313,0.198 10 false 25 4.552,0.969 4.979,1.208 0.427,0.24 10 false F103 2.938,0.667 3.146,0.844 0.208,0.177 10 false 2 2.219,1.344 2.531,1.542 0.313,0.198 10 false W 4.281,6.313 4.594,6.51 0.313,0.198 10 false SB 2.448,3.417 2.76,3.615 0.313,0.198 10 false P 1.802,3.417 2.115,3.615 0.313,0.198 10 false W 2.406,4.188 2.719,4.385 0.313,0.198 10 false W 1.271,3.521 1.479,3.698 0.208,0.177 10 false 4 4.938,0.969 7.021,1.229 2.083,0.26 10 false No. 4 CAN Junction Connector 2.938,3.51 3.146,3.688 0.208,0.177 10 false 5 1.26,3.875 1.469,4.052 0.208,0.177 10 false 8 1.813,4.177 2.125,4.375 0.313,0.198 10 false B 0.292,6.115 2.438,6.333 2.146,0.219 10 false *1: for Navigation Receiver Type 0.302,6.51 3.854,7.073 3.552,0.563 10 false *2: for Radio and Display Type 3.188,6.604 3.5,6.802 0.313,0.198 10 false 16 4.229,5.979 4.438,6.156 0.208,0.177 10 false 8 5.771,4.219 5.979,4.396 0.208,0.177 10 false 9 3.188,5.979 3.5,6.177 0.313,0.198 10 false 18 4.208,6.604 4.521,6.802 0.313,0.198 10 false 17 3.604,7.302 4.135,7.479 0.531,0.177 10 false 120 Ω 3.115,6.313 3.427,6.51 0.313,0.198 10 false W 5.094,7.125 7,7.354 1.906,0.229 10 false Combination Meter Assembly 5.594,5.083 5.906,5.271 0.313,0.188 10 false F71 5.917,5.083 7.063,5.656 1.146,0.573 10 false Radio and Display Receiver Assembly*2 5.885,3.104 7.104,3.594 1.219,0.49 10 false Navigation Receiver Assembly*1 5.302,4.917 5.615,5.115 0.313,0.198 10 false W 5.344,4.167 5.656,4.365 0.313,0.198 10 false L 5.708,4.604 6.021,4.802 0.313,0.198 10 false 10 5.781,2.26 5.99,2.438 0.208,0.177 10 false 9 5.719,2.635 6.031,2.833 0.313,0.198 10 false 10 5.323,2.167 5.635,2.365 0.313,0.198 10 false L 5.292,2.927 5.604,3.125 0.313,0.198 10 false W 5.729,0.156 7,0.406 1.271,0.25 10 false x: Suspected Area 4.521,2.24 4.677,2.438 0.156,0.198 10 false 6 4.51,2.875 4.823,3.073 0.313,0.198 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 60 km/h (37 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*

*: w/ Smart Entry and Start System




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C298354
1.531,0.125 1.958,0.448 0.427,0.323 0.833,1.854 0.938,1.854 0.938,1.854 1.333,1.385 true 1.927,1.865 1.781,1.865 1.781,1.865 1.479,1.396 true 1.625,0.188 2.083,0.385 0.458,0.198 10 false F22 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.427,1.771 1.042,1.969 0.615,0.198 10 false CANL 2.01,1.771 2.625,1.969 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the F22 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-17 (CANH) - F22-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 3 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the F22 combination meter assembly connector.


b.
C292333C02
1.583,0.167 1.979,0.469 0.396,0.302 2.635,1 2.76,0.229 2.76,0.229 2.833,0.229 true 2.927,1.927 2.844,1.927 2.844,1.927 2.625,1.094 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.656,0.208 2.115,0.406 0.458,0.198 10 false A43 2.906,0.125 3.365,0.354 0.458,0.229 10 false CANH 2.979,1.833 3.396,2.052 0.417,0.219 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-13 (CANH) - A43-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1AR-FE) A
OK (for 2GR-FE) B
NG C



A

B

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the A43 ECM connector.


b.

Disconnect the F102 No. 3 CAN junction connector.

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.75 1.917,1.75 1.917,1.75 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.417 2,1.417 2,1.417 2.604,2.094 true 1.833,2.917 2.083,2.917 2.083,2.917 2.646,2.323 true 1.833,1.083 2.083,1.083 2.083,1.083 2.885,2.104 true 2,3.167 2.25,3.167 2.25,3.167 2.906,2.323 true 2.167,0.75 2.417,0.75 2.417,0.75 3.146,2.104 true 2.25,3.417 2.5,3.417 2.5,3.417 3.167,2.333 true 2.5,0.49 2.75,0.49 2.75,0.49 3.385,2.104 true 4.25,0.5 4,0.5 4,0.5 3.635,2.115 true 4.667,0.75 4.417,0.75 4.417,0.75 3.885,2.104 true 2.75,3.604 3,3.604 3,3.604 3.396,2.333 true 4.25,3.604 4,3.604 4,3.604 3.646,2.323 true 4.667,3.417 4.417,3.417 4.417,3.417 3.885,2.323 true 4.917,3.167 4.667,3.167 4.667,3.167 4.146,2.323 true 5.25,2.917 5,2.917 5,2.917 4.396,2.323 true 5.333,2.635 5.083,2.635 5.083,2.635 4.646,2.333 true 4.917,1.083 4.667,1.083 4.667,1.083 4.135,2.104 true 5.25,1.417 5,1.417 5,1.417 4.385,2.104 true 5.333,1.75 5.083,1.75 5.083,1.75 4.635,2.104 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.083,1.667 1.698,1.896 0.615,0.229 10 false CANH*b 1.146,2.521 1.76,2.75 0.615,0.229 10 false CANL*b 1.094,1.333 1.708,1.563 0.615,0.229 10 false CANH*c 1.271,2.813 1.885,3.042 0.615,0.229 10 false CANL*c 1.26,0.979 1.875,1.208 0.615,0.229 10 false CANH*d 1.448,3.073 2.063,3.302 0.615,0.229 10 false CANL*d 1.604,0.635 2.469,0.865 0.865,0.229 10 false CANH*e 1.708,3.323 2.417,3.573 0.708,0.25 10 false CANL*e 1.958,0.385 2.573,0.615 0.615,0.229 10 false CANH*f 2.25,3.51 2.865,3.74 0.615,0.229 10 false CANL*f 4.323,0.396 4.938,0.625 0.615,0.229 10 false CANH*g 4.323,3.51 4.938,3.74 0.615,0.229 10 false CANL*g 4.74,0.667 5.354,0.896 0.615,0.229 10 false CANH*h 4.74,3.323 5.354,3.552 0.615,0.229 10 false CANL*h 3.271,0.146 3.885,0.344 0.615,0.198 10 false F102 4.99,3.073 5.604,3.302 0.615,0.229 10 false CANL*i 5.323,2.823 5.938,3.052 0.615,0.229 10 false CANL*j 5.406,2.542 6.021,2.771 0.615,0.229 10 false CANL*k 4.99,0.99 5.604,1.219 0.615,0.229 10 false CANH*i 5.323,1.323 5.938,1.552 0.615,0.229 10 false CANH*j 5.406,1.656 6.021,1.885 0.615,0.229 10 false CANH*k
*a Front view of wire harness connector
(No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to ECM *d to Air Conditioning Amplifier Assembly
*e to Airbag Sensor Assembly *f to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
*g to Main Body ECU (Multiplex Network Body ECU) *h to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
*i to 4WD ECU Assembly
(for AWD)
*j to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
*k to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F102-1 (CANH) - F102-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
F102-2 (CANH) - F102-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F102-3 (CANH) - F102-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F102-4 (CANH) - F102-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
F102-5 (CANH) - F102-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*1
F102-6 (CANH) - F102-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
F102-7 (CANH) - F102-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*2
F102-8 (CANH) - F102-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU assembly*3
F102-9 (CANH) - F102-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly*4
F102-10 (CANH) - F102-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Network gateway ECU*5


·

*1: w/ Toyota Parking Assist-sensor System

·

*2: w/ Smart Entry and Start System

·

*3: for AWD

·

*4: w/ Automatic Headlight Beam Level Control System

·

*5: w/ Blind Spot Monitor System or Parking Assist Monitor System



Result:
Result Proceed to
OK A
NG (No. 4 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (ECM main line) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 3 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F102 No. 3 CAN junction connector.


b.

Disconnect the F103 No. 4 CAN junction connector.

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.833 1.927,1.833 1.927,1.833 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.469 2.01,1.469 2.01,1.469 2.604,2.094 true 1.813,3.01 2.125,3.01 2.125,3.01 2.646,2.323 true 1.802,1.042 2.135,1.042 2.135,1.042 2.885,2.104 true 1.99,3.323 2.385,3.323 2.385,3.323 2.906,2.323 true 2.208,0.635 2.458,0.635 2.458,0.635 3.146,2.104 true 2.438,3.542 2.771,3.542 2.771,3.542 3.167,2.333 true 3.75,0.594 3.51,0.594 3.51,0.594 3.385,2.115 true 4.552,0.833 4.333,0.833 4.333,0.833 3.635,2.115 true 3.74,3.552 3.448,3.552 3.448,3.552 3.396,2.313 true 4.417,3.25 4.167,3.25 4.167,3.25 3.667,2.323 true 5.01,2.948 4.656,2.948 4.656,2.948 4.146,2.313 true 5.104,1.26 4.896,1.26 4.896,1.26 4.125,2.094 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.104,1.75 1.719,1.979 0.615,0.229 10 false CANH*b 1.146,2.531 1.76,2.76 0.615,0.229 10 false CANL*b 1.094,1.375 1.708,1.604 0.615,0.229 10 false CANH*c 1.271,2.927 1.885,3.156 0.615,0.229 10 false CANL*c 1.25,0.948 1.865,1.177 0.615,0.229 10 false CANH*d 1.448,3.229 2.063,3.458 0.615,0.229 10 false CANL*d 1.646,0.542 2.26,0.771 0.615,0.229 10 false CANH*e 1.906,3.458 2.521,3.688 0.615,0.229 10 false CANL*e 3.823,0.5 4.438,0.729 0.615,0.229 10 false CANH*f 3.823,3.448 4.438,3.677 0.615,0.229 10 false CANL*f 4.615,0.75 5.417,1 0.802,0.25 10 false CANH*g*h 4.49,3.167 5.208,3.469 0.719,0.302 10 false CANL*g*h 3.281,0.156 3.896,0.354 0.615,0.198 10 false F103 5.177,1.167 5.792,1.396 0.615,0.229 10 false CANH*i 5.083,2.854 5.698,3.083 0.615,0.229 10 false CANL*i
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to Skid Control ECU (Brake Actuator Assembly) *d to DLC3
*e to Steering Sensor *f to Power Steering ECU Assembly
*g to Navigation Receiver Assembly
(for Navigation Receiver Type)
*h to Radio and Display Receiver Assembly
(for Radio and Display Type)
*i to Combination Meter Assembly - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F103-1 (CANH) - F103-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction connector
F103-2 (CANH) - F103-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Skid control ECU (brake actuator assembly)
F103-3 (CANH) - F103-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher DLC3
F103-4 (CANH) - F103-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
F103-5 (CANH) - F103-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
F103-6 (CANH) - F103-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Navigation receiver assembly*1
F103-6 (CANH) - F103-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*2
F103-8 (CANH) - F103-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


·

*1: for Navigation Receiver Type

·

*2: for Radio and Display Type



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (DLC3 branch line) D
NG (Combination meter assembly main line) E



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

E

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C292403
1.5,0.104 1.875,0.417 0.375,0.313 2.042,0.823 2.396,0.323 2.396,0.323 2.531,0.323 true 1.552,1.938 1.708,1.938 1.708,1.938 2.042,1.438 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 1.563,0.156 1.875,0.354 0.313,0.198 10 false F25 2.604,0.229 3.219,0.427 0.615,0.198 10 false CANH 1.115,1.844 1.729,2.042 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-6 (CANH) - F25-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR