Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098499 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. When a signal received is the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

B307854
4.438,3.427 6.104,3.938 1.667,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 1.354,3.042 4.073,3.531 2.719,0.49 10 false Back Door Opener Switch Assembly*1 1.458,1.896 3.26,2.302 1.802,0.406 10 false Back Door Lock Assembly 1.354,5.115 3.823,5.438 2.469,0.323 10 false Back Door Opener Switch Assembly*2 1.469,1.729 1.75,1.896 0.281,0.167 10 false X18 1.354,2.854 1.813,3.167 0.458,0.313 10 false q1 1.354,4.927 1.677,5.208 0.323,0.281 10 false q1 5.188,5.469 6.813,6.177 1.625,0.708 10 false Certification ECU (Smart Key ECU Assembly)*2 5.188,5.302 5.667,5.583 0.479,0.281 10 false F12 4.094,0.615 4.635,1.052 0.542,0.438 10 false 4H 5.01,2.635 5.396,3 0.385,0.365 10 false F19 4.094,1.323 4.552,1.635 0.458,0.313 10 false 4H 2.729,1.177 3.26,1.469 0.531,0.292 10 false ACT+ 2.698,4.542 3.115,4.865 0.417,0.323 10 false BDSU 1.875,4.542 2.24,4.844 0.365,0.302 10 false GND 2.917,2.542 3.292,2.885 0.375,0.344 10 false UL 1.896,2.542 2.302,2.917 0.406,0.375 10 false E 2.875,0.49 3.365,0.854 0.49,0.365 10 false D+ 1.531,1.188 2,1.49 0.469,0.302 10 false ACT- 1.323,1.198 1.656,1.49 0.333,0.292 10 false 1 3.177,1.177 3.542,1.479 0.365,0.302 10 false 2 3.167,0.5 3.448,0.76 0.281,0.26 10 false 3 3.188,2.531 3.708,3.042 0.521,0.51 10 false 3 1.719,2.531 1.958,2.792 0.24,0.26 10 false 2 4.146,1.104 4.458,1.292 0.313,0.188 10 false 4 4.104,0.417 4.427,0.698 0.323,0.281 10 false 33 5.052,2.438 5.24,2.604 0.188,0.167 10 false 18 5.094,4.552 5.375,4.865 0.281,0.313 10 false 5 3.177,4.542 3.552,4.917 0.375,0.375 10 false 3 1.708,4.542 2.094,4.927 0.385,0.385 10 false 2 5.365,4.667 6.073,5.042 0.708,0.375 10 false TSW5 5.375,0.615 5.927,0.885 0.552,0.271 10 false BCTY 5.375,2.646 5.969,2.958 0.594,0.313 10 false BDSU 5.375,1.302 5.917,1.719 0.542,0.417 10 false TR+ 0.771,6.24 2.802,6.51 2.031,0.271 10 false : CAN Communication Line 0.448,5.563 3.146,5.844 2.698,0.281 10 false *1: w/o Smart Entry and Start System 0.448,5.896 3.146,6.135 2.698,0.24 10 false *2: w/ Smart Entry and Start System 3.656,1.698 5.271,2.229 1.615,0.531 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

w/ Smart Entry and Start System:

Before performing this troubleshooting procedure , perform troubleshooting for the smart entry and start system (for Entry Function) (Back Door Entry Unlock Function does not Operate) first.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>Back Door Entry Unlock Function does not Operate

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

*: for LHD




PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Smart Entry and Start System A
w/ Smart Entry and Start System B



A

2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)

B

8.INSPECT BACK DOOR LOCK ASSEMBLY
2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)
a.

Check the power door lock basic functions.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

The power door lock basic functions operate properly.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Back Door Open)

NG

3.READ VALUE USING GTS (Back Door Open)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open Back door lock signal Prohibit or Permit Prohibit: Back door locked
Permit: Back door unlocked
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open
50003 123 27
OK:

The GTS displays Permit or Prohibit according to the back door lock assembly operation.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (Trunk and Back-Door Open)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.PERFORM ACTIVE TEST USING GTS (Trunk and Back-Door Open)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk and Back-Door Open Back door lock motor OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Trunk and Back-Door Open
50004 123 3
OK:

The back door lock assembly unlatches when ON is selected.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (Back Door Open Handle SW)

NG

8.INSPECT BACK DOOR LOCK ASSEMBLY
5.READ VALUE USING GTS (Back Door Open Handle SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open Handle SW Back door opener switch signal OFF or ON OFF: Back door opener switch not pushed
ON: Back door opener switch pushed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open Handle SW
50003 123 29
OK:

The GTS displays ON or OFF according to the back door opener switch assembly operation.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
6.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Inspect the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
q1-3 (UL) - F19-18 (BDSU) Always Below 1 Ω
q1-2 (E) - Body ground Always Below 1 Ω
q1-3 (UL) or F19-18 (BDSU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BACK DOOR LOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the 4H instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X18-2 (ACT+) - 4H-4 Always Below 1 Ω
X18-3 (D+) - 4H-33 Always Below 1 Ω
X18-1 (ACT-) - Body ground Always Below 1 Ω
X18-2 (ACT+) or 4H-4 - Body ground Always 10 kΩ or higher
X18-3 (D+) or 4H-33 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK BACK DOOR OPEN OPERATION
11.CHECK BACK DOOR OPEN OPERATION
a.

Check that the back door can be opened.

OK:

The back door can be opened.


Result:
Proceed to
OK
NG




OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)