Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the intake air control valve assembly (intake air surge tank assembly) in response to changes in the engine load in order to increase the intake efficiency using the Acoustic Control Induction System (ACIS).

When the engine speed is between 0 and 4450 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the actuator (on status) to close the intake air control valve assembly. Under other conditions, the intake air control valve assembly is open.

A316076E01
1.26,1.958 1.094,0.938 1.094,0.938 1.344,0.938 false 1.521,2.146 1.25,2.5 1.25,2.5 1.167,2.5 true 3.281,1.719 3.5,0.917 3.5,0.917 3.667,0.917 false 4.667,2.083 4.75,0.979 4.75,0.979 4.917,0.979 false 5.25,3.667 5.25,4.417 5.25,4.417 5.25,4.5 false 0.135,0.073 1.052,0.323 0.917,0.25 10 false Engine Speed 1.135,0.51 3,0.74 1.865,0.229 10 false Throttle Valve Opening Angle 1.427,0.875 2.427,1.125 1,0.25 10 false ACIS Actuator 3.698,0.844 4.688,1.177 0.99,0.333 10 false Throttle Position Sensor 3.344,2.74 4.281,3.083 0.938,0.344 10 false Throttle Valve Opening Angle 0.094,2.396 1.156,2.885 1.063,0.49 10 false Intake Air Control Valve Assembly 4.969,0.896 7.042,1.24 2.073,0.344 10 false Intake Air Control Valve Assembly Closed (Actuator: on) 2.458,2.833 2.625,3.01 0.167,0.177 10 false 1 1.948,2.833 2.115,3.01 0.167,0.177 10 false 3 1.438,2.844 1.604,3.021 0.167,0.177 10 false 5 1.458,1.146 1.625,1.323 0.167,0.177 10 false 6 1.969,1.146 2.135,1.323 0.167,0.177 10 false 4 2.479,1.146 2.646,1.323 0.167,0.177 10 false 2 4.313,2.792 4.615,3 0.302,0.208 10 false 60° 4.583,4.542 6.656,4.885 2.073,0.344 10 false Intake Air Control Valve Assembly Open (Actuator: off) 2.469,5.604 2.635,5.781 0.167,0.177 10 false 1 1.958,5.604 2.125,5.781 0.167,0.177 10 false 3 1.438,5.604 1.604,5.781 0.167,0.177 10 false 5 1.458,3.896 1.625,4.073 0.167,0.177 10 false 6 1.958,3.896 2.125,4.073 0.167,0.177 10 false 4 2.479,3.906 2.646,4.083 0.167,0.177 10 false 2 0.438,0.729 1.354,0.979 0.917,0.25 10 false ECM 6.198,4.052 7.115,4.302 0.917,0.25 10 false Engine Speed 4.396,3.885 5.313,4.135 0.917,0.25 10 false 0 rpm 6.115,3.865 6.781,4.167 0.667,0.302 10 false 4450 rpm 0.448,3.5 1.365,3.75 0.917,0.25 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
1.

The voltage of terminal ACIS of the ECM is low when the intake air control valve assembly (for acoustic control induction system) is off.

2.

The engine has been started.


·

Open or short in intake air control valve assembly (for acoustic control induction system) circuit

·

Intake air control valve assembly (for acoustic control induction system)

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A315971E02
0.74,1.01 0.99,1.177 0.25,0.167 10 false 1H 0.792,0.813 0.958,0.979 0.167,0.167 10 false 1 1.042,1.167 1.708,1.333 0.667,0.167 10 false EFI-MAIN 0.479,2.521 1.063,2.688 0.583,0.167 10 false FL MAIN 0.604,3.198 1.104,3.365 0.5,0.167 10 false Battery 1.333,2.302 2.552,2.635 1.219,0.333 10 false Semiconductor Pwr Integration ECU 1.688,1.781 2.354,1.948 0.667,0.167 10 false EFI MAIN 2.542,1.5 2.792,1.667 0.25,0.167 10 false 1G 2.542,1.01 2.792,1.177 0.25,0.167 10 false 1G 2.604,0.813 2.771,0.979 0.167,0.167 10 false 7 2.604,1.313 2.771,1.479 0.167,0.167 10 false 6 3.135,1.167 3.802,1.333 0.667,0.167 10 false EFI NO. 3 3.792,0.906 3.958,1.073 0.167,0.167 10 false 2 5.094,0.906 5.26,1.073 0.167,0.167 10 false 1 3.854,1.365 4.188,1.531 0.333,0.167 10 false C9 3.854,1.531 5.313,2.083 1.458,0.552 10 false Intake Air Control Valve Assembly (Intake Air Surge tank Assembly) 5.375,0.813 5.625,0.979 0.25,0.167 10 false 47 5.333,2.76 5.667,2.927 0.333,0.167 10 false A43 5.375,1.01 5.625,1.177 0.25,0.167 10 false C1 5.385,2.563 5.635,2.729 0.25,0.167 10 false 46 6.083,3.729 6.5,3.896 0.417,0.167 10 false ECM 5.698,2.76 6.167,2.927 0.469,0.167 10 false MREL 5.698,1.01 6.083,1.177 0.385,0.167 10 false ACIS

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

e.

Check if operating noise can be heard when operating the intake air control valve assembly using the GTS.

OK:

Operating noise can be heard.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT INTAKE AIR SURGE TANK ASSEMBLY (INTAKE AIR CONTROL VALVE ASSEMBLY OPERATION)
2.INSPECT INTAKE AIR SURGE TANK ASSEMBLY (INTAKE AIR CONTROL VALVE ASSEMBLY OPERATION)
a.

Inspect the intake air surge tank assembly (intake air control valve assembly).

Click hereEngine / Hybrid System>2GR-FE (INTAKE / EXHAUST)>INTAKE AIR CONTROL VALVE(for ACIS)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ASSEMBLY)

NG

REPLACE INTAKE AIR SURGE TANK ASSEMBLY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ASSEMBLY)
A194326C06
0.469,1.958 0.917,2.24 0.448,0.281 0.24,0.208 0.625,0.76 0.385,0.552 10 false *a 0.615,2.021 1.042,2.292 0.427,0.271 10 false C9
*a Front view of wire harness connector
(to Intake Air Control Valve Assembly)


a.

Disconnect the intake air control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C9-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INTAKE AIR CONTROL VALVE ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the intake air control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C9-1 - C1-47 (ACIS) Always Below 1 Ω
C9-1 or C1-47 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INTAKE AIR CONTROL VALVE ASSEMBLY)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the intake air control valve assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-7 - C9-2 Always Below 1 Ω
1G-7 or C9-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR