Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM3160E _59 Vehicle Exterior _019720 MIRROR (EXT) _0101072 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (driver door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (driver door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (driver door), to adjust the mirror surface position.

WIRING DIAGRAM

B293969E82
0.146,4.26 1.354,4.76 1.208,0.5 10 false Outer Mirror Switch Assembly 0.146,4.073 1.021,4.271 0.875,0.198 10 false I10*1, H11*2 1.844,4.083 2.167,4.292 0.323,0.208 10 false F20 1.844,4.26 3.5,4.792 1.656,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 0.896,0.875 1.396,1.177 0.5,0.302 10 false MSW 1.344,0.74 1.677,1.052 0.333,0.313 10 false 15*1 2.01,0.75 2.385,1.094 0.375,0.344 10 false 5 1.344,2.073 1.698,2.302 0.354,0.229 10 false 13*1 2.021,2.073 2.323,2.344 0.302,0.271 10 false 4 1.344,3.354 1.771,3.604 0.427,0.25 10 false 16*1 2.01,3.354 2.25,3.552 0.24,0.198 10 false 6 1.042,2.208 1.458,2.51 0.417,0.302 10 false M+ 1.135,3.49 1.51,3.854 0.375,0.365 10 false E 2.271,0.875 2.75,1.208 0.479,0.333 10 false MIRS 2.271,2.219 2.771,2.521 0.5,0.302 10 false MIRB 2.271,3.49 2.781,3.74 0.51,0.25 10 false MIRE 1.01,5.323 2.708,5.469 1.698,0.146 10 false : CAN Communication Line 4.896,0.854 5.167,1.104 0.271,0.25 10 false MH 4.896,2.188 5.167,2.406 0.271,0.219 10 false M+ 4.896,3.479 5.167,3.667 0.271,0.188 10 false MV 5.219,0.75 5.427,1 0.208,0.25 10 false 9 5.219,2.094 5.552,2.385 0.333,0.292 10 false 10 5.219,3.344 5.427,3.594 0.208,0.25 10 false 1 3.802,4.25 5.375,4.74 1.573,0.49 10 false Outer Mirror Control ECU Assembly (Driver Door) 3.802,4.073 4.708,4.26 0.906,0.188 10 false z10*1, z9*2 5.656,4.208 7.115,4.75 1.458,0.542 10 false Outer Rear View Mirror Assembly (Driver Door) 3.313,5.313 4.146,5.5 0.833,0.188 10 false *1: for LHD 4.479,5.313 5.313,5.5 0.833,0.188 10 false *2: for RHD 1.344,0.573 1.677,0.885 0.333,0.313 10 false 13*2 1.344,1.906 1.698,2.135 0.354,0.229 10 false 15*2 1.344,3.188 1.771,3.438 0.427,0.25 10 false 12*2

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror*1 OFF or ON OFF: Mirror select switch off
ON: Mirror select switch R switch on
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror*2 OFF or ON OFF: Mirror select switch off
ON: Mirror select switch L switch on
-
Mirror Position SW (R) Mirror adjust switch signal (Right) OFF or ON OFF: Mirror adjust switch not pushed right
ON: Mirror adjust switch pushed right
Check with the mirror select switch L or R selected
Mirror Position SW (L) Mirror adjust switch signal (Left) OFF or ON OFF: Mirror adjust switch not pushed left
ON: Mirror adjust switch pushed left
Check with the mirror select switch L or R selected
Mirror Position SW (Up) Mirror adjust switch signal (Up) OFF or ON OFF: Mirror adjust switch not pushed up
ON: Mirror adjust switch pushed up
Check with the mirror select switch L or R selected
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) OFF or ON OFF: Mirror adjust switch not pushed down
ON: Mirror adjust switch pushed down
Check with the mirror select switch L or R selected

*1: for RHD

*2: for LHD


Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (MIRROR SURFACE)

NG

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (MIRROR SURFACE)
a.

Remove the outer rear view mirror assembly (driver door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly (driver door) (mirror surface).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I10*1 or H11*2 outer mirror switch assembly.

*1: for LHD

*2: for RHD



b.

Disconnect the F20 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I10-16 (E) - F20-6 (MIRE) Always Below 1 Ω
I10-13 (M+) - F20-4 (MIRB) Always Below 1 Ω
I10-15 (MSW) - F20-5 (MIRS) Always Below 1 Ω
I10-16 (E) or F20-6 (MIRE) - Body ground Always 10 kΩ or higher
I10-13 (M+) or F20-4 (MIRB) - Body ground Always 10 kΩ or higher
I10-15 (MSW) or F20-5 (MIRS) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H11-12 (E) - F20-6 (MIRE) Always Below 1 Ω
H11-15 (M+) - F20-4 (MIRB) Always Below 1 Ω
H11-13 (MSW) - F20-5 (MIRS) Always Below 1 Ω
H11-12 (E) or F20-6 (MIRE) - Body ground Always 10 kΩ or higher
H11-15 (M+) or F20-4 (MIRB) - Body ground Always 10 kΩ or higher
H11-13 (MSW) or F20-5 (MIRS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR