Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights.

WIRING DIAGRAM

for Halogen Headlight


E287445
1.031,0.333 2.865,0.531 1.833,0.198 10 false from Battery 0.771,1.542 1.083,1.74 0.313,0.198 10 false 1B 0.802,1.333 0.958,1.531 0.156,0.198 10 false 1 1.188,1.406 1.802,1.604 0.615,0.198 10 false BATT 1.385,1.688 2.24,1.906 0.854,0.219 10 false H-LP LO LH 1.365,3 2.219,3.219 0.854,0.219 10 false H-LP LO RH 2.24,2.333 3.094,2.552 0.854,0.219 10 false H-LP LH-LO 2.229,3.646 3.083,3.865 0.854,0.219 10 false H-LP RH-LO 3.094,1.417 3.708,1.615 0.615,0.198 10 false HLLS 3.156,1.938 3.771,2.135 0.615,0.198 10 false HILL 3.083,3.271 3.698,3.469 0.615,0.198 10 false HLLR 1.146,4.156 3.469,4.365 2.323,0.208 10 false Semiconductor Pwr Integration ECU 4.854,1.958 5.938,2.521 1.083,0.563 10 false Instrument Panel Junction Block Assembly 3.615,1.542 3.927,1.74 0.313,0.198 10 false 1D 4.542,1.542 4.854,1.74 0.313,0.198 10 false 4F 6.021,1.552 6.635,1.75 0.615,0.198 10 false HRLY 5.74,1.438 6.052,1.635 0.313,0.198 10 false 15 4.542,1.344 4.854,1.542 0.313,0.198 10 false 27 3.615,2.052 3.927,2.25 0.313,0.198 10 false 1E 3.656,1.333 3.813,1.531 0.156,0.198 10 false 8 3.656,1.854 3.813,2.052 0.156,0.198 10 false 3 3.604,3.375 3.917,3.573 0.313,0.198 10 false 1E 3.667,3.177 3.823,3.375 0.156,0.198 10 false 2 3,4.969 3.156,5.167 0.156,0.198 10 false 2 2.99,6.542 3.146,6.74 0.156,0.198 10 false 2 1.792,4.969 1.948,5.167 0.156,0.198 10 false 1 1.792,6.531 1.948,6.729 0.156,0.198 10 false 1 2,4.969 2.156,5.167 0.156,0.198 10 false E 2,6.542 2.156,6.74 0.156,0.198 10 false E 2.698,4.979 3.01,5.177 0.313,0.198 10 false LO 2.698,6.542 3.01,6.74 0.313,0.198 10 false LO 2.135,5.292 3.365,5.49 1.229,0.198 10 false Low Beam 2.135,6.865 3.365,7.063 1.229,0.198 10 false Low Beam 1.667,5.625 1.979,5.823 0.313,0.198 10 false A28 1.667,5.771 3.219,6 1.552,0.229 10 false Headlight Assembly RH 1.677,7.198 1.99,7.396 0.313,0.198 10 false A20 1.677,7.333 3.229,7.563 1.552,0.229 10 false Headlight Assembly LH 5.396,7.833 5.708,8.031 0.313,0.198 10 false MB 5.396,8 7.073,8.406 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU)


for LED Headlight


E289443
1.188,0.521 2.021,0.75 0.833,0.229 10 false from Battery 3.469,1.396 4.01,1.625 0.542,0.229 10 false HLLS 4.781,1.906 5.854,2.458 1.073,0.552 10 false Instrument Panel Junction Block Assembly 1.781,5.469 3.615,5.677 1.833,0.208 10 false Light Control LED ECU RH 1.198,1.292 1.354,1.49 0.156,0.198 10 false 1 4.063,1.313 4.219,1.51 0.156,0.198 10 false 8 5.635,5.625 5.792,5.823 0.156,0.198 10 false 3 4.083,5.406 4.24,5.604 0.156,0.198 10 false 2 4.073,8 4.229,8.198 0.156,0.198 10 false 1 4.073,7.667 4.229,7.865 0.156,0.198 10 false 2 4.063,1.833 4.219,2.031 0.156,0.198 10 false 3 4.052,3.156 4.208,3.354 0.156,0.198 10 false 2 4.823,1.323 5.063,1.531 0.24,0.208 10 false 27 5.594,7.938 5.833,8.146 0.24,0.208 10 false 16 5.594,1.323 5.833,1.531 0.24,0.208 10 false 15 4.073,5.708 4.229,5.906 0.156,0.198 10 false 1 4.01,1.51 4.323,1.708 0.313,0.198 10 false 1D 4,3.354 4.313,3.552 0.313,0.198 10 false 1E 4.813,1.51 5.125,1.708 0.313,0.198 10 false 4F 5.583,1.51 5.896,1.708 0.313,0.198 10 false MB 1.156,1.51 1.469,1.708 0.313,0.198 10 false 1B 4.01,2.031 4.323,2.229 0.313,0.198 10 false 1E 5.573,8.125 5.885,8.323 0.313,0.198 10 false F19 5.563,5.833 5.875,6.031 0.313,0.198 10 false F19 1.75,6.281 2.063,6.479 0.313,0.198 10 false A29 1.74,8.573 2.052,8.771 0.313,0.198 10 false A21 1.573,1.365 2.188,1.563 0.615,0.198 10 false BATT 2.635,3.635 3.469,3.833 0.833,0.198 10 false H-LP RH-LO 2.625,2.313 3.458,2.51 0.833,0.198 10 false H-LP LH-LO 1.771,1.677 2.604,1.875 0.833,0.198 10 false H-LP LO LH 1.75,2.979 2.583,3.177 0.833,0.198 10 false H-LP LO RH 3.469,3.24 3.906,3.448 0.438,0.208 10 false HLLR 3.781,5.406 4.104,5.635 0.323,0.229 10 false LO 3.49,1.906 3.896,2.104 0.406,0.198 10 false HILL 5.969,1.5 6.51,1.729 0.542,0.229 10 false HRLY 5.958,5.844 6.5,6.073 0.542,0.229 10 false RLEW 5.969,8.125 6.51,8.354 0.542,0.229 10 false LLEW 3.781,7.677 4.104,7.906 0.323,0.229 10 false LO 3.854,5.708 4.177,5.938 0.323,0.229 10 false S 1.531,4.115 3.823,4.365 2.292,0.25 10 false Semiconductor Pwr Integration ECU 3.854,8.01 4.177,8.24 0.323,0.229 10 false S 1.365,7.823 1.688,8.052 0.323,0.229 10 false E 1.375,5.531 1.698,5.76 0.323,0.229 10 false E 1.167,5.531 1.396,5.792 0.229,0.26 10 false 3 1.167,7.823 1.396,8.083 0.229,0.26 10 false 3 2.063,4.802 3.208,5.031 1.146,0.229 10 false Low Beam (LED) 2.052,7.094 3.198,7.323 1.146,0.229 10 false Low Beam (LED) 1.771,7.75 3.604,7.958 1.833,0.208 10 false Light Control LED ECU LH 1.74,6.427 3.573,6.635 1.833,0.208 10 false Headlight Assembly RH 1.74,8.719 3.573,8.927 1.833,0.208 10 false Headlight Assembly LH 5.396,8.698 7.052,9.135 1.656,0.438 10 false Main Body ECU (Multiplex Network Body ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Relay Headlight relay (Low beam headlights) ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Headlight Relay
50004 123 14
OK:

Headlight relay operates. (Low beam headlights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU
2.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU
a.

Remove the semiconductor pwr integration ECU from the No. 1 engine room relay block and No. 1 junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Inspect the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE)

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE)
a.
E272254C15
1.5,0.417 1.917,0.667 0.417,0.25 1.792,1.375 2.344,1.698 false 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 1.625,0.458 1.938,0.656 0.313,0.198 10 false 1B 2.385,1.698 2.823,1.896 0.438,0.198 10 false BATT
*a Component without semiconductor pwr integration ECU connected
(No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-8 (HLLS) - 4F-27 Always Below 1 Ω
1D-8 (HLLS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E259752C10
1.229,0.302 1.563,0.531 0.333,0.229 4.594,0.458 4.927,0.688 0.333,0.229 4.354,1.5 4.594,1.104 false 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.323,0.333 1.635,0.531 0.313,0.198 10 false 4F 4.677,0.5 4.99,0.698 0.313,0.198 10 false MB 4.177,1.531 4.792,1.729 0.615,0.198 10 false HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4F-27 - MB-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY