Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0097123 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light (clock assembly) when the immobiliser is set (no key is in the ignition key cylinder).

·

The main body ECU (multiplex network body ECU) blinks the security indicator light (clock assembly) when the theft deterrent system is in the arming preparation state or alarm sounding state.


WIRING DIAGRAM

B271008E28
4.49,1.115 4.844,1.427 0.354,0.313 10 false F66 4.448,2.958 4.823,3.281 0.375,0.323 10 false F19 4.49,1.281 5.906,1.823 1.417,0.542 10 false Transponder Key ECU Assembly 4.448,3.115 6.094,3.604 1.646,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 1.333,1.115 1.729,1.354 0.396,0.24 10 false G7 1.344,1.271 2.792,1.844 1.448,0.573 10 false Security Indicator Light (Clock Assembly) 4.771,0.594 5.031,0.76 0.26,0.167 10 false IND 4.771,2.5 5.031,2.667 0.26,0.167 10 false IND 4.552,0.49 4.729,0.677 0.177,0.188 10 false 8 4.51,2.375 4.74,2.635 0.229,0.26 10 false 15 2.74,0.49 2.948,0.646 0.208,0.156 10 false 9 1.552,0.49 1.74,0.646 0.188,0.156 10 false 8 1.719,0.604 2.333,0.802 0.615,0.198 10 false E 2.458,0.604 3.073,0.802 0.615,0.198 10 false LP

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19

Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D



A

2.CHECK SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) OPERATION

B

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

5.INSPECT SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)
2.CHECK SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on.



Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG D



A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G7 security indicator light (clock assembly) connector.


b.

Disconnect the F66 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-8 (IND) - G7-9 (LP) Always Below 1 Ω
F66-8 (IND) or G7-9 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G7 security indicator light (clock assembly) connector.


b.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-15 (IND) - G7-9 (LP) Always Below 1 Ω
F19-15 (IND) or G7-9 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)
a.

Remove the security indicator light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

Inspect the security indicator light (clock assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - BODY GROUND)

NG

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - BODY GROUND)
a.

Disconnect the G7 security indicator light (clock assembly) connector.


b.

Disconnect F66 transponder key ECU assembly connector.


c.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-8 (IND) - G7-9 (LP) Always Below 1 Ω
F19-15 (IND) - G7-9 (LP) Always Below 1 Ω
G7-8 (E) - Body ground Always Below 1 Ω
F66-8 (IND) or G7-9 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new or known good one.

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


HINT:

Refer to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)