Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination is Always Dark  


DESCRIPTION

The combination meter assembly receives signals from this circuit to adjust the illumination of the combination meter assembly. The combination meter assembly sets the illumination level based on the user operation of the light control switch knob (combination meter assembly).

WIRING DIAGRAM

E143765E86
0.083,3.104 1.719,3.458 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 2.927,3.167 3.021,3.354 0.094,0.188 10 false : 3.01,3.188 4.656,3.542 1.646,0.354 10 false CAN Communication Line 5.115,3.115 6.927,3.615 1.813,0.5 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



HINT:
·

The meter illumination dims when the taillights are turned on.

·

Setting the meter illumination to maximum brightness cancels the above dimming of the meter illumination.

·

Setting the meter illumination to minimum brightness turns off the meter illumination.

·

Before starting the following inspection, check if Lighting System DTCs are output.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.READ VALUE USING GTS (LIGHT SENSOR ILLUMINANCE)

B

2.READ VALUE USING GTS (LIGHT SENSOR ILLUMINANCE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
Body Electrical > Main Body > Data List
Tester Display
Light Sensor Illuminance
50003 123 279

Result:
Result Proceed to
The output value changes according to the ambient light level. A
The output value does not change according to the ambient light level. B



A

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (MULTIPLEX NETWORK BODY ECU)

B

CHECK CUSTOMIZE PARAMETER SETTING (SENSITIVITY)

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

OK:

The operation of the combination meter assembly returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE COMBINATION METER ASSEMBLY