Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination does not Dim at Night  


DESCRIPTION

In this circuit, the combination meter assembly receives auto dimmer signals from the main body ECU (multiplex network body ECU) via the CAN communication system. When the combination meter assembly receives an auto dimmer signal, it dims the meter illumination (warning and indicator lights).

The main body ECU (multiplex network body ECU) determines whether it is daytime or nighttime based on the waveform transmitted from the automatic light control sensor. If the main body ECU (multiplex network body ECU) determines that it is nighttime and the headlight dimmer switch assembly is in the tail, head or AUTO position, the ECU sends an auto dimmer signal to the combination meter assembly.

According to this signal, the combination meter assembly dims the meter illumination.

HINT:

When the meter illumination does not dim at night, there may be a malfunction in the automatic light control sensor, main body ECU (multiplex network body ECU), CAN communication system, wire harness, connector, or combination meter assembly.


WIRING DIAGRAM

E143765E86
0.083,3.104 1.719,3.458 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 2.927,3.167 3.021,3.354 0.094,0.188 10 false : 3.01,3.188 4.656,3.542 1.646,0.354 10 false CAN Communication Line 5.115,3.115 6.927,3.615 1.813,0.5 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



HINT:
·

The automatic light control sensor sensitivity can be customized.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS

·

Setting the meter illumination to maximum brightness prevents the meter illumination from dimming when the headlight dimmer switch assembly is changed to the tail, head or AUTO position at night. Therefore, check the meter illumination setting before proceeding to the following steps.

·

Before starting the following inspection, check if Lighting System DTCs are output.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.READ VALUE USING GTS (LIGHT SENSOR ILLUMINANCE)

B

2.READ VALUE USING GTS (LIGHT SENSOR ILLUMINANCE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
Body Electrical > Main Body > Data List
Tester Display
Light Sensor Illuminance
50003 123 279

Result:
Result Proceed to
The output value changes according to the ambient light level. A
The output value does not change according to the ambient light level. B



A

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

CHECK CUSTOMIZE PARAMETER SETTING (SENSITIVITY)

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

OK:

The operation of the combination meter assembly returns to normal.


HINT:

The combination meter assembly controls the meter illumination based on an auto dimmer signal from the main body ECU (multiplex network body ECU). If the combination meter assembly does not dim when the headlight dimmer switch assembly is in the tail, head or AUTO position at night, it may be for one of 2 reasons. The first reason is that the main body ECU (multiplex network body ECU) did not send an auto dimmer signal. The second is that the combination meter assembly did not dim the meter illumination even though the combination meter assembly received an auto dimmer signal.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE COMBINATION METER ASSEMBLY