Home › Vehicle Exterior › WINDOW / GLASS › GLASS HATCH OPENER SYSTEM
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106115 GLASS HATCH OPENER SYSTEM J

WINDOW / GLASS  GLASS HATCH OPENER SYSTEM  Glass Hatch Opener System does not Operate  


DESCRIPTION

The glass hatch opener system enables the back door glass to be opened when the glass hatch opener switch assembly is pressed.

WIRING DIAGRAM

B361015E02
0.167,3.75 0.74,4.146 0.573,0.396 10 false F18 0.177,3.906 1.823,4.24 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 3.167,3.667 4.896,4 1.729,0.333 10 false Glass Hatch Opener Switch Assembly 3.167,3.5 3.688,3.833 0.521,0.333 10 false X10 3,2.5 3.427,2.802 0.427,0.302 10 false X11 3,2.667 4.917,2.833 1.917,0.167 10 false Back Window Lock Assembly 3.646,1.396 5.063,1.563 1.417,0.167 10 false G/H NO. 1 6.063,0.646 6.896,0.813 0.833,0.167 10 false from Battery 4.833,0.813 5.75,0.979 0.917,0.167 10 false DOOR BACK 3.417,3.125 3.583,3.292 0.167,0.167 10 false 2 3.604,3.125 3.771,3.292 0.167,0.167 10 false B 4.281,3.125 4.563,3.333 0.281,0.208 10 false L 4.458,3.115 4.625,3.281 0.167,0.167 10 false 1 0.979,3.188 1.479,3.354 0.5,0.167 10 false GOSW 1.063,2.292 1.479,2.458 0.417,0.167 10 false GCTY 1.031,0.656 1.531,0.823 0.5,0.167 10 false GHRY 1.542,0.552 1.792,0.719 0.25,0.167 10 false 21 1.531,2.198 1.781,2.365 0.25,0.167 10 false 27 1.531,3.104 1.781,3.271 0.25,0.167 10 false 28 3.167,2.198 3.333,2.365 0.167,0.167 10 false 1 3.167,1.958 3.333,2.125 0.167,0.167 10 false 3 3.354,1.958 3.521,2.125 0.167,0.167 10 false + 4.469,1.979 4.635,2.146 0.167,0.167 10 false - 4.656,1.958 4.823,2.125 0.167,0.167 10 false 2 4.344,0.563 4.51,0.729 0.167,0.167 10 false 2 4.354,1.063 4.521,1.229 0.167,0.167 10 false 4 4.354,0.875 4.521,1.042 0.167,0.167 10 false 5 3.469,0.563 3.635,0.729 0.167,0.167 10 false 1 3.469,0.854 3.635,1.021 0.167,0.167 10 false 3 3.354,2.198 3.688,2.365 0.333,0.167 10 false +

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

2.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)

B

3.READ VALUE USING GTS
2.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)
a.

Check if the entry glass hatch open function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry glass hatch open function operates normally.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Glass Hatch Courtesy Switch Back window courtesy switch signal OFF or ON OFF: Back door glass closed
ON: Back door glass open
-
Body Electrical > Main Body > Data List
Tester Display
Glass Hatch Courtesy Switch
50003 123 156
OK:

The GTS display changes correctly in response to the opening and closing operation of the back door glass.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

GO TO LIGHTING SYSTEM (Proceed to Back Door Courtesy Switch Circuit)

4.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Glass Hatch Opener Switch Glass hatch opener switch signal OFF or ON OFF: Glass hatch opener switch not operated
ON: Glass hatch opener switch operated
-
Body Electrical > Main Body > Data List
Tester Display
Glass Hatch Opener Switch
50003 123 157
OK:

The GTS display changes correctly in response to the operation of the glass hatch opener switch.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS

NG

11.CHECK HARNESS AND CONNECTOR (GLASS HATCH OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
5.PERFORM ACTIVE TEST USING GTS
a.

Enter the following menus: Body Electrical / Main Body / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Glass Hatch Open Operate Glass Hatch OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Glass Hatch Open
50004 123 31
OK:

The glass hatch opens.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT G/H NO. 1 RELAY
6.INSPECT G/H NO. 1 RELAY
a.

Inspect the G/H No. 1 relay.

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (G/H NO. 1 RELAY - BATTERY)

NG

REPLACE G/H NO. 1 RELAY

7.CHECK HARNESS AND CONNECTOR (G/H NO. 1 RELAY - BATTERY)
a.
B361016C01
0.167,0.167 0.417,0.333 0.25,0.167 10 false *1
*1 G/H No. 1 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G/H No. 1 relay holder terminal 2 - Body ground Always 11 to 14 V
G/H No. 1 relay holder terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (G/H NO. 1 RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (G/H NO. 1 RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.
B361016C01
0.167,0.167 0.417,0.333 0.25,0.167 10 false *1
*1 G/H No. 1 Relay Holder


Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G/H No. 1 relay holder terminal 1 - F18-21 (GHRY) Always Below 1 Ω
G/H No. 1 relay holder terminal 1 or F18-21 (GHRY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT BACK WINDOW LOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BACK WINDOW LOCK ASSEMBLY
a.

Remove the back window lock assembly.

Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>REMOVAL


b.

Inspect the back window lock assembly.

Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BACK WINDOW LOCK ASSEMBLY - G/H NO. 1 RELAY AND BODY GROUND)

NG

REPLACE BACK WINDOW LOCK ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BACK WINDOW LOCK ASSEMBLY - G/H NO. 1 RELAY AND BODY GROUND)
a.
B361016C01
0.167,0.167 0.417,0.333 0.25,0.167 10 false *1
*1 G/H No. 1 Relay Holder


Disconnect the X11 back window lock assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X11-3 (+) - G/H No. 1 relay holder terminal 3 Always Below 1 Ω
X11-3 (+) or G/H No. 1 relay holder terminal 3 - Body ground Always 10 kΩ or higher
X11-2 (-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (GLASS HATCH OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the X10 glass hatch opener switch assembly connector.


b.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X10-2 (B) - F18-28 (GOSW) Always Below 1 Ω
X10-2 (B) or F18-28 (GOSW) - Body ground Always 10 kΩ or higher
X10-1 (L) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT GLASS HATCH OPENER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT GLASS HATCH OPENER SWITCH ASSEMBLY
a.

Remove the glass hatch opener switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>REMOVAL


b.

Inspect the glass hatch opener switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE GLASS HATCH OPENER SWITCH ASSEMBLY