Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the engine switch on (IG) and the driver door closed, pressing the manual lock or unlock switch on the power window regulator master switch assembly while holding a seat memory switch (driver door) (M1 or M2 switch) will register the transmitter recognition code into the seat memory switch (driver door) that was pressed. After registration is completed, the answer back buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 of the seat memory switches are pressed simultaneously.

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the manual lock/unlock function by using the door control switch (power window regulator master switch assembly).

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Manual lock/unlock function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK SMART ENTRY AND START SYSTEM (for Start Function)

NG

2.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine starts normally when the engine switch is pressed while carrying the key and with the brake pedal depressed.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION

NG

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
OK A
NG (seat position memory function does not operate normally) B
NG (seat position restoring function does not operate normally) C




A

4.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

4.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*2 ON or OFF ON: Driver door open
OFF: Driver door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*1 ON or OFF ON: Driver door open
OFF: Driver door closed
-

*1: for LHD

*2: for RHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

ON or OFF appears on the screen according to the driver door condition.



Result:
Proceed to
OK
NG



OK

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory registration operates normally.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6*
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*
-

*: Although the item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

On the GTS display, it is confirmed that the memory call has been registered.



Result:
Proceed to
OK
NG



OK

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory registration and automatic memory call function operate normally.



Result:
Proceed to
OK
NG



OK

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate)

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory registration operates normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

10.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
10.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory registration operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)