When a door is unlocked using the wireless unlock function, the certification ECU (smart key ECU assembly) sends a key ID signal to the main body ECU (multiplex network body ECU). When a door is unlocked using the entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call and memory command information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the memory commands and performs the memory call operation according to predetermined control timing values.
The seat position will not be stored if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING
If the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: for LHD
Check the operation of the power seats.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check whether seat positions can be stored in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check whether seat positions can be restored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check the operation of memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| OK | A |
| NG (power seat operation) | B |
| NG (seat position memory) | C |
| NG (seat position restoring) | D |
| NG (memory call registration) | E |
A
B
C
D
E
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Memory call function linked with the wireless unlock function does not operate | A |
| Memory call function linked with the entry unlock function does not operate | B |
| Both memory call function linked with the wireless unlock function and entry unlock function do not operate | C |
A
B
C
Check the wireless unlock function of the wireless door lock control system.
Wireless unlock function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the memory call function, check the outer mirror operation.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Result | Proceed to |
|---|---|
| Outer mirrors operate normally | A |
| Outer mirrors do not operate normally | B |
A
B
Temporarily replace the position control ECU and switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the wireless unlock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the wireless unlock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the entry unlock function of the smart entry and start system (for entry function).
Entry unlock function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the memory call function, check the outer mirror operation.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Outer mirrors operate normally | A |
| Outer mirrors do not operate normally | B |
A
B
Temporarily replace the position control ECU and switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the entry unlock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the entry unlock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the memory call function and check the outer mirror operation.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Outer mirrors operate normally | A |
| Outer mirrors do not operate normally | B |
A
B
Temporarily replace the position control ECU and switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the wireless unlock and entry unlock function operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 | NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* |
- |
*: Although the item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Tester Display |
|---|
| Seat Memory No1 |
| Seat Memory No2 |
On the GTS display, it is confirmed that the memory switch which is linked with a key ID has a memorized seat position. (For example, on the GTS display, "Mem SW No. w/KeyID1" displays "MEM SW1" and "Seat Memory No1" displays "Mem".)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly (driver door) signal*2 | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| FL Door Courtesy SW | Front door courtesy light switch assembly (driver door) signal*1 | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
*1: for LHD
*2: for RHD
| Tester Display |
|---|
| FR Door Courtesy SW |
| FL Door Courtesy SW |
On the GTS screen, each item changes between ON and OFF according to the above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the memory registration and automatic memory call function of the memory call function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Memory call function linked with the wireless unlock and entry unlock function operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG