Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107346 AUTOMATIC TRANSAXLE ASSEMBLY A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

If automatic transaxle parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

Hide 11361J 1.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A205885

Turn the crankshaft to gain access to the removable locations of the 6 drive plate and torque converter setting bolts and remove each drive plate and torque converter setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored bolt.



Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 48829A 5.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 6.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 7.REMOVE FRONT STABILIZER BAR

Hide 8.REMOVE STEERING LINK ASSEMBLY

Hide 51100G 9.REMOVE FRONT FRAME ASSEMBLY

Hide 12.DISCONNECT WIRE HARNESS

a.
C297900C02
2.24,0.833 2.49,1.073 0.25,0.24 10 true *a
*a Park/Neutral Position Switch Connector


Disconnect the park/neutral position switch connector.


b.

Remove the 2 bolts and disengage the 5 clamps to disconnect the wire harness from the automatic transaxle assembly.


Hide 16587 13.REMOVE RADIATOR PIPE CLAMP

a.
C296626C01
2.104,1.406 2.573,1.406 true 1,0.448 1.188,0.448 1.188,0.448 1.333,0.833 true 1.01,1.094 1.198,1.094 1.198,1.094 1.344,1.479 true 0.771,1.031 1,1.26 0.229,0.229 10 true *1 2.615,1.333 2.875,1.552 0.26,0.219 10 true *2 0.781,0.354 1,0.583 0.219,0.229 10 true *a
*1 Breather Plug
*2 Radiator Pipe Clamp
*a Air Fuel Ratio Sensor Wire Harness


Disengage the air fuel ratio sensor wire harness.


b.

Disengage the breather plug from the clamp.


c.

Remove the bolt and radiator pipe clamp with the clamp from the engine assembly.


d.
C296627

Remove the clamp from the radiator pipe clamp.


Hide 36118A 14.REMOVE TRANSFER STIFFENER PLATE RH

a.
C296629C01
2.094,0.365 2.219,0.146 2.219,0.146 2.385,0.146 true 0.854,0.229 1.042,0.229 1.042,0.229 1.167,0.396 true 2.427,0.063 2.688,0.292 0.26,0.229 10 true *2 0.615,0.156 0.833,0.385 0.219,0.229 10 true *1
*1 Transfer Stiffener Plate RH
*2 Rear Engine Mounting Bracket


Remove the 4 bolts and transfer stiffener plate RH from the rear engine mounting bracket and the transfer assembly.


Hide 30500 15.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.

Using the transmission jack attachment, set the automatic transaxle assembly on a transmission jack.

NOTICE:
·

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

·

To prevent the automatic transaxle oil pan sub-assembly from deforming, do not place any attachments onto the automatic transaxle oil pan sub-assembly of the automatic transaxle assembly.

·

Hold the engine assembly with a suitable adapter, such as a rope, during the operation.




b.
C298984

Remove the 11 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 36100 16.REMOVE TRANSFER ASSEMBLY

Hide 12311A 17.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C296611

Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.


Hide 18.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C296612

Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle assembly.


Hide 33823 19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C296613

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.


Hide 33403M 20.REMOVE SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

a.
C296614

Remove the bolt and speedometer driven hole (ATM) cover sub-assembly from the automatic transaxle assembly.


b.

Remove the O-ring from the speedometer driven hole (ATM) cover sub-assembly.


Hide 32000 21.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C298985

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 32101 23.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY