Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108187 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B360751C01
0.688,0.083 1,0.24 0.313,0.156 10 false *a 2.5,0.083 2.813,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements of areas "a" through "p" are within each standard range.

B362063N01
0.625,0.875 0.781,1.073 0.156,0.198 10 false a 0.479,1.365 0.635,1.563 0.156,0.198 10 false b 2.156,0.417 2.313,0.615 0.156,0.198 10 false c 2.365,1.031 2.521,1.229 0.156,0.198 10 false d 3.865,0.521 4.021,0.719 0.156,0.198 10 false e 4.115,1.115 4.271,1.313 0.156,0.198 10 false f 5.969,1.271 6.125,1.469 0.156,0.198 10 false g 6.313,1.063 6.469,1.26 0.156,0.198 10 false h 6.042,4.219 6.198,4.417 0.156,0.198 10 false i 6.49,3.927 6.646,4.125 0.156,0.198 10 false j 4.615,4.479 4.771,4.677 0.156,0.198 10 false k 5.063,4.198 5.219,4.396 0.156,0.198 10 false l 2.177,4.5 2.333,4.698 0.156,0.198 10 false m 1.698,4.208 1.854,4.406 0.156,0.198 10 false n 0.729,4.146 0.885,4.344 0.156,0.198 10 false o 0.25,3.865 0.406,4.063 0.156,0.198 10 false p

Standard Clearance
Area Measurement Area Measurement
a 3.35 to 6.35 mm (0.132 to 0.250 in.) b 6.15 to 9.15 mm (0.242 to 0.360 in.)
c 3.35 to 6.35 mm (0.132 to 0.250 in.) d 2.35 to 5.35 mm (0.0925 to 0.211 in.)
e 3.35 to 6.35 mm (0.132 to 0.250 in.) f 0.95 to 3.95 mm (0.0374 to 0.156 in.)
g 2.3 to 6.3 mm (0.0906 to 0.248 in.) h -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
i 3.2 to 5.6 mm (0.126 to 0.220 in.) j -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
k 3.2 to 5.6 mm (0.126 to 0.220 in.) l -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
m 2.8 to 5.2 mm (0.110 to 0.205 in.) n -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
o 2.8 to 5.2 mm (0.110 to 0.205 in.) p -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)


Hide 75086 2.REMOVE FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY

Hide 3.REMOVE FRONT WHEEL

Hide 53852B 4.REMOVE FRONT WHEEL OPENING EXTENSION PAD

HINT:

Use the same procedure as for the RH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


Hide 53876A 5.REMOVE FRONT FENDER LINER

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


Hide 53827B 6.REMOVE FRONT FENDER SIDE PANEL PROTECTOR

a.
B362060

Remove the 2 clips and front fender side panel protector.


Hide 7.ADJUST FRONT DOOR

NOTICE:

Make sure to turn the ignition switch off when adjusting door lock strikers.


a.
B362061

Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the 4 hinge bolts on the door and adjust the door position.


d.

Tighten the 4 hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B362062

Using a T40 "TORX" socket wrench, slightly loosen 2 the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 53827B 8.INSTALL FRONT FENDER SIDE PANEL PROTECTOR

a.

Install the front fender side panel protector with 2 new clips.


Hide 53876A 9.INSTALL FRONT FENDER LINER

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSTALLATION


Hide 53852B 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD

HINT:

Use the same procedure as for the RH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSTALLATION


Hide 75086 12.INSTALL FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY