Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › ENGINE
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109588 ENGINE G

1AR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY


b.

Check that nothing is caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise.

HINT:

If a malfunction exists, replace the V-ribbed belt tensioner assembly.




Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 234 29
Standard Ignition Timing:

5 to 15° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard Ignition Timing:

8 to 12° BTDC at idle


NOTICE:
·

Turn off all electrical systems and the A/C.

·

Check the ignition timing with the cooling fans off.

·

When checking the ignition timing, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A122830C42
1.094,0.604 1.552,1.063 false 1.76,1.656 1.375,2.042 false 0.927,1.063 1.042,1.219 0.115,0.156 10 false 1 0.927,1.469 1.042,1.625 0.115,0.156 10 false 9 1.104,1.469 1.281,1.625 0.177,0.156 10 false 10 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.51,1.469 1.688,1.625 0.177,0.156 10 false 12 1.719,1.469 1.896,1.625 0.177,0.156 10 false 13 1.927,1.469 2.104,1.625 0.177,0.156 10 false 14 2.125,1.469 2.302,1.625 0.177,0.156 10 false 15 2.333,1.469 2.51,1.625 0.177,0.156 10 false 16 1.135,1.063 1.25,1.219 0.115,0.156 10 false 2 1.344,1.063 1.458,1.219 0.115,0.156 10 false 3 1.552,1.063 1.667,1.219 0.115,0.156 10 false 4 1.75,1.063 1.865,1.219 0.115,0.156 10 false 5 1.958,1.063 2.073,1.219 0.115,0.156 10 false 6 2.156,1.063 2.271,1.219 0.115,0.156 10 false 7 2.365,1.063 2.479,1.219 0.115,0.156 10 false 8 0.135,0.146 0.302,0.323 0.167,0.177 10 false *a 0.875,0.479 1.188,0.677 0.313,0.198 10 false CG 1.156,1.958 1.469,2.156 0.313,0.198 10 false TC
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.

Remove the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


iii.
A210177

Pull out the wire harness shown in the illustration.

NOTICE:

After checking, wrap the wire harness with tape.



iv.

Connect the clip of a timing light to the ignition coil wire harness.

NOTICE:

Use a timing light that detects primary signals.



v.

Start the engine and run it at idle.


vi.

Check the ignition timing at idle.

Standard Ignition Timing:

8 to 12° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




vii.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


viii.

Check the ignition timing at idle.

Standard Ignition Timing:

5 to 15° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ix.

Confirm that the ignition timing advances immediately when the engine speed is increased.


x.

Disconnect the clip of the timing light from the ignition coil wire harness.


xi.

Install the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

v.

Read the value displayed on the tester.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the engine idle speed, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A122830C43
0.823,1.958 0.969,1.667 false 0.927,1.063 1.042,1.219 0.115,0.156 10 false 1 0.927,1.469 1.042,1.625 0.115,0.156 10 false 9 1.104,1.469 1.281,1.625 0.177,0.156 10 false 10 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.51,1.469 1.688,1.625 0.177,0.156 10 false 12 1.719,1.469 1.896,1.625 0.177,0.156 10 false 13 1.927,1.469 2.104,1.625 0.177,0.156 10 false 14 2.125,1.469 2.302,1.625 0.177,0.156 10 false 15 2.333,1.469 2.51,1.625 0.177,0.156 10 false 16 1.135,1.063 1.25,1.219 0.115,0.156 10 false 2 1.344,1.063 1.458,1.219 0.115,0.156 10 false 3 1.552,1.063 1.667,1.219 0.115,0.156 10 false 4 1.75,1.063 1.865,1.219 0.115,0.156 10 false 5 1.958,1.063 2.073,1.219 0.115,0.156 10 false 6 2.156,1.063 2.271,1.219 0.115,0.156 10 false 7 2.365,1.063 2.479,1.219 0.115,0.156 10 false 8 0.167,0.115 0.521,0.354 0.354,0.24 10 false *a 0.688,2 1.083,2.177 0.396,0.177 10 false TAC
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals can cause damage to electrical components.



ii.

Start the engine and run it at idle.


iii.

Inspect the engine idle speed.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the engine idle speed, the transaxle should be in neutral or park.




iv.

Turn the engine switch off.


v.

Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.




d.

Disconnect the 4 fuel injector connectors.


e.
A283834

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1450 kPa (14.8 kgf/cm2, 210 psi)


Minimum Compression Pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Pressure Difference between Each Cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure as quickly as possible.





f.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding engine oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.




g.

Connect the 4 fuel injector connectors.



i.

Clear the DTCs.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle with motor body assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI system:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter sub-assembly

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle with motor body assembly)