Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0109291 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Opened or Closed Using the Power Back Door Switch  


DESCRIPTION

When the back door cannot be opened or closed using the rear door control switch, one of the following may be malfunctioning: 1) rear door control switch circuit, 2) multiplex network door ECU or 3) main body ECU (multiplex network body ECU).

WIRING DIAGRAM

B358086
1.292,0.958 1.448,1.156 0.156,0.198 10 false 1 3.667,1.073 4.125,1.271 0.458,0.198 10 false PBDS 2.896,0.969 3.052,1.167 0.156,0.198 10 false 4 3.458,0.958 3.667,1.177 0.208,0.219 10 false 5 2.427,0.969 2.885,1.167 0.458,0.198 10 false MSW 1.49,0.969 1.948,1.167 0.458,0.198 10 false MSE 1.427,1.427 1.885,1.625 0.458,0.198 10 false F1 1.427,1.583 3.417,1.823 1.99,0.24 10 false Rear Door Control Switch 3.219,1.813 3.677,2.01 0.458,0.198 10 false F18 3.229,1.979 4.865,2.375 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.427,1.958 6.552,2.354 1.125,0.396 10 false Multiplex Network Door ECU 0.75,2.354 2.74,2.594 1.99,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power back door system after confirming that the communication system is functioning properly.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open SW Rear door control switch signal ON or OFF ON: Rear door control switch on
OFF: Rear door control switch off
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open SW
50003 123 95
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.REPLACE MULTIPLEX NETWORK DOOR ECU

NG

5.INSPECT REAR DOOR CONTROL SWITCH
2.REPLACE MULTIPLEX NETWORK DOOR ECU
a.

Temporarily replace the multiplex network door ECU with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.INITIALIZE MULTIPLEX NETWORK DOOR ECU
3.INITIALIZE MULTIPLEX NETWORK DOOR ECU
a.

Perform the initialization for the multiplex network door ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CHECK POWER BACK DOOR SYSTEM
4.CHECK POWER BACK DOOR SYSTEM
a.

Check that the power back door system operates normally.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power back door system operates normally A
Power back door system does not operate B



A

END (MULTIPLEX NETWORK DOOR ECU WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.INSPECT REAR DOOR CONTROL SWITCH
a.

Remove the rear door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the rear door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR DOOR CONTROL SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (REAR DOOR CONTROL SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the F1 rear door control switch connector.


b.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-4 (MSW) - F18-5 (PBDS) Always Below 1 Ω
F1-1 (MSE) - Body ground Always Below 1 Ω
F1-4 (MSW) or F18-5 (PBDS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR